Side reactions polarity

Bromination in polar solvents usually gives /n j -3,4-dibromo-2-methyl-3-buten-2-ol in nonpolar solvents, with incandescent light, the cis isomer is the principal product (194). Chlorine adds readily up to the tetrachloro stage, but yields are low because of side reactions (195). 

Replacement of Labile Chlorines. When PVC is manufactured, competing reactions to the normal head-to-tail free-radical polymerization can sometimes take place. These side reactions are few ia number yet their presence ia the finished resin can be devastating. These abnormal stmctures have weakened carbon—chlorine bonds and are more susceptible to certain displacement reactions than are the normal PVC carbon—chlorine bonds. Carboxylate and mercaptide salts of certain metals, particularly organotin, zinc, cadmium, and antimony, attack these labile chlorine sites and replace them with a more thermally stable C—O or C—S bound ligand. These electrophilic metal centers can readily coordinate with the electronegative polarized chlorine atoms found at sites similar to stmctures (3—6). 

To be eligible to living anionic polymerization a vinylic monomer should carry an electron attracting substituent to induce polarization of the unsaturation. But it should contain neither acidic hydrogen, nor strongly electrophilic function which could induce deactivation or side reactions. Typical examples of such monomers are p-aminostyrene, acrylic esters, chloroprene, hydroxyethyl methacrylate (HEMA), phenylacetylene, and many others. 

Carbon dioxide 53 55). If excess C02 and polar solvents are used the carboxylation is quantitative and free of side reactions. In nonpolar solvents association phenomena favor ketone formation 55). An alternate way to get re-carboxylic polymers is to react the living sites with a cyclic anhydride 561. 

The authors concluded that the side reactions normally observed in amine-initiated NCA polymerizations are simply a consequence of impurities. Since the main side reactions in these polymerizations do not involve reaction with adventitious impurities such as water, but instead reactions with monomer, solvent, or polymer (i.e., termination by reaction of the amine-end with an ester side chain, attack of DMF by the amine-end, or chain transfer to monomer) [11, 12], this conclusion does not seem to be well justified. It is likely that the role of impurities (e.g., water) in these polymerizations is very complex. A possible explanation for the polymerization control observed under high vacuum is that the impurities act to catalyze side reactions with monomer, polymer, or solvent. In this scenario, it is reasonable to speculate that polar species such as water can bind to monomers or the propagating chain-end and thus influence their reactivity. 

The more polar components have been characterised by FTICR—MS and HPLC-ESI-MS, and include excess PEG [CH30(E0)nH and HO(EO) Hl starting materials, confirmation of which was obtained by comparison with commercial standards [29]. ESI—MS, FTICR—MS and H NMR data analysis also indicated the presence of the Si—O—C byproduct 3, abbreviated to MDOH-0-(E0)ra-CH2CH=CH2, shown in Fig. 2.8.7. The formation of 3 can occur through side reactions of the... 

The chemistry of the reactions involved in coupling peptides is the same as that for coupling TV-alkoxycarbonylamino acids. However, the oxazolone that is formed by the activated peptide is chirally unstable, it is formed more readily, and there is an added impetus for it to form because the rate of bond formation between segments is lower. In addition, segments usually have to be coupled in polar solvents because they are insoluble in nonpolar solvents, and polar solvents promote the undesirable side reaction. The result is that the number of procedures actually used for coupling peptides is rather small. The methods in question are addressed below. 

The choice of the solvent is critical, and both non-coordinating solvents or polar aprotic solvents such as DMF can lead to intractable product mixtures. Solvent effects and side-reactions in chromium carbene benzannulation reactions have been thoroughly investigated [207,333,334]. 

However, morpholine-4-carboxylic acid 2-hydroxy-1-methyl-ethyl ester is formed by the reaction of PC and the substrate morpholine in an undesired side reaction. By use of 1.4-dioxane or the pyrrolidones as mediator s3 about 30 to 45% of the morphoUne is consumed by this side reaction. The by-product is contained in the PC phase and can not be extracted to the non-polar product phase. The selectivity to the desired amines is lowered, because of the consiunption of the morphoUne. Thus, PC has to be substituted by another polar solvent (e.g. water, methanol or ethylene glycol) in future experiments. The lactates react with the morphoUne, too resulting in the corresponding amide. Overall, the hydroaminomethylation in the TMS systems PC/dodecane/lactate results in a conversion of 1-octene of about 80%, but in selectivities to the amines of only 50 to 60%. 

---