Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Plasticator screw

Not only are there two classes of deformation, there are also two modes in which deformation can be produced simple shear and simple tension. The actual action during melting, as in the usual screw plasticator is extremely complex, with all types of shear-tension combinations. Together with engineering design, deformation determines the pumping efficiency of a screw plasticator and... [Pg.446]

A distinction should be made between machine conditions and processing variables. Machine conditions are basically temperature, pressure, and processing time (such as screw rotation/rpm, and so on) in the case of a screw plasticator, die and mold temperature and pressure, machine output rate (lb./hr), and the like. Processing variables are more specific such as the melt temperature in the die or mold, melt flow rate, and pressure used. [Pg.454]

Spalding, M.A., Hyun, K.S., and Cohen, B.R., An Experimental Study of the Frictional and Viscous Forces Responsible for Solids Conveying and Melting in Single-Screw Plasticating Extruders, SPE ANTEC Tech. Papers, 43, 202 (1997)... [Pg.129]

Spalding, M.A., Powers, J.R., Wagner, P.A., and Hyun, K. S., Flow Surging in Single-Screw, Plasticating Extruders, SPEANTEC Tech. Papers, 46, 254 (2000)... [Pg.129]

Zitzenbacher, G., Karlbauer, R., and Thiel, H., A New Calculation Model and Optimization Method for Maddock Mixers in Single-Screw Plasticating Technology, Int. Polym. Process., 22, 73 (2007)... [Pg.384]

Figure 12.27 The solids-conveying section of a single-screw, plasticating extruder with a worn feed casing. The schematic is not to scale, and it shows a ledge formed between the oversized (worn) feed casing and the flange of a new barrel... Figure 12.27 The solids-conveying section of a single-screw, plasticating extruder with a worn feed casing. The schematic is not to scale, and it shows a ledge formed between the oversized (worn) feed casing and the flange of a new barrel...
Potente H. Existing scale-up rules for single-screw plasticating extruders. Int Polym Process 1991 4 267-278. [Pg.366]

A. Berlis, E. Broyer, C. Mund, and Z. Tadmor, Flow Patterns in Aprtially Filled Extruder Screw, Plastics Polym., 41, 145-148 (June 1973). [Pg.320]

R. Y. Chang, C. W. Hsu, W. H. Yang, W. L. Yang, and D. C. Hsu, Three Dimensional Numerical Analysis of the Single Screw Plasticating Extrusion Process, SPE ANTEC Tech. [Pg.517]

See other pages where Plasticator screw is mentioned: [Pg.280]    [Pg.4]    [Pg.185]    [Pg.186]    [Pg.187]    [Pg.333]    [Pg.383]    [Pg.522]    [Pg.674]    [Pg.76]    [Pg.3]    [Pg.447]    [Pg.473]    [Pg.473]    [Pg.475]    [Pg.477]    [Pg.479]    [Pg.481]    [Pg.483]    [Pg.485]    [Pg.487]    [Pg.489]    [Pg.491]    [Pg.493]    [Pg.495]    [Pg.497]    [Pg.499]    [Pg.501]    [Pg.503]    [Pg.505]    [Pg.517]    [Pg.518]   
See also in sourсe #XX -- [ Pg.491 ]



SEARCH



Engineering Design Method for Plasticating Screws

Extrusion plasticating single-screw extruder

Melting Zone in a Plasticating Single Screw Extruder

Non-screw plasticating

Plasticating Single-Screw Extruders

Plasticating screw

Plasticating single screw extrusion

Plastication screws

Plastication screws

Plastics extruders single screw

Plastics extruders twin screw

Reciprocating screw plasticator

SCREW PLASTICIZATION

SCREW PLASTICIZATION

Screw and plastic

Screw design, processing plastic

Screw plasticating injection molding

Screw plasticator frictional heat

Screw plasticizing

Screw-barrel plasticator

Single-screw plasticating extruder

The Single Screw Plasticating Extrusion Process

© 2024 chempedia.info