Sandia labs

Granoff, B. Baca, T. M. Thomas, M. G. Noles, G. P. "Chemical Studies on Synthoil Mineral Matter Effects", Sandia Labs. Energy Rept. No. SAN-78-1113, 1978. 

This work is currently supported by NSF grant DMR 9313371 and by the Materials Science Center at Cornell University under NSF Grant DMR 9121654. We are particularly grateful to the staff of the Cornell Nanofabrication Facility for their assistance in creating the periodic starting stractures. The LEEM experiments on Si were carried out in collaboration with Ruud Tromp and Marion Mankos at IBM, Yorktown Heights, NY. Norm Bartelt of Sandia Labs, Livermore, CA has modeled the kinetics of the island and hole decay on the 2-D gratings. 

R.A. Benham F.H. Mathews, SC-78-1535C, Sandia Labs (1978) 21) G.E. Jones, JAppl-... 

Wilson, Yaw of Repose on Spinning Shells , SC-RR-70-155, Sandia Labs, Albuquerque (1970) 6) Ibid, Effect of Yaw of Repose on Ballistic... 

E.F. Hartman co-workers at Sandia Labs, Albuquerque (private communications) noted in Ref 257 234) J.R. Ward et al, Effect of... 

Sandia Labs, Albuquerque (1976) [Gould reports that from measurements of deton vel made on 2-grain/foot, Al-sheathed mild detonating fuze (MDF) contg HNS, the thermal stability of small diam charges (or MDF) of HNS is greatly reduced by exposures above 200°, and that the procedure used to prepare the bulk HNS powder also has a decided effect on the thermal stability of the resulting MDF] 5) P.E. Rouse, Jr,... 

Donaldson D.O. Lee, Comparative Thermal Behavior of HMX and TATB Base Explosives, SC-DR-720729, Sandia Labs, Albuquerque (1972) 23) Not used 24) L. Avrami et... 

Figures 14.2 and 14.3 show closeups of poly-Si micromachines from Sandia Labs, manufactured by using several poly-Si CMP processes. Figure 14.2 depicts the gear wheels of a 10 1 transmission. Due to CMP, the gears are completely planar. Figure 14.3 shows the alignment clips for positioning the gears. The two layers of gears are clearly visible. More examples that show where the five-layer surface micromachining process has been employed are...

To counter this concern, Sandia labs developed another foam product that was faster acting and less corrosive, DF-200. DF-200 has a lower concentration of peroxide and surfactants and contains an activator to increase the speed with which it breaks down agents. 

J. F. Cuderman, (1972a). Research Report Sandia Labs. SC-RR-71 0756. 

J. Szymborski, Final Report to Sandia Labs, 1982, personal communication. 

B. Mason, GM seeks help from Sandia Labs. The Valley Times, 93(281) (2005). 

C. B. Bailey and R. E. Jones, Brief Instructions for Using the Sandia Numerical Mathematical Subroutine Library on the CDC6600, SLA-74-0095. Sandia Lab., Albuquerque, New Mexico, 1974. 

FIGURE 2 Representative reactor pumped laser signals (a) CO RPL excited by Sandia Labs SPR-II (FBR) (b) Ar RPL excited by Sandia Labs SPR-II (FBR) (c) Xe RPL excited by Sandia Labs ACRR (analogous to pulsed TRIGA reactor). 

L. L. BONZON/ F. M. MORRIS, and F. V. THOME, Annular Core Pulse Reactor (ACPR) Experimenter s Manual, SLA-73-1017, Sandia Labs. (Aug. 1974). 

Subcriticality Design Considerations for LMFBR Spent Fuel Shipping Casks, /. S. Phil bin, S. A. Dupree (Sandia Labs)... 

J. A. ANDElRS etal., "PARC Research Design and Development," SAMD76-0587, Sandia Labs., to be... 

Only a few years after the introduction of CMP for the fabrication of More Moore devices, the first MEMS devices were demonstrated by Sandia labs, which employed pofishing for poly-Si layer planarization (Sniegowski, 1996). Later, CMP was adopted for the fabrication of many More than Moore devices. 

University of Michigan (and Sandia Labs) USA Monitoring and control... 

---