Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Regaine

The concluding chapters, Chapters XVI through XVIII, take up the important subjects of physical and chemical adsorption of vapors and gases, and heterogeneous catalysis. As with the earlier chapters, the approach is relatively quantitative and problem assignments regain importance. [Pg.802]

Attention is directed to a previous discussion of what happens when the electronic basis is extended to the complete Hilbert space, [79] p. 60 especially Eqs. (2.17)-(2.18). It is shown there that in that event the full symmeti of the invariance group is regained (in effect, through the cancellation of the... [Pg.149]

The role of the base is apparently primarily that of a proton remover from the reactive methylene group thus if B represents the base, reaction (i) gives the carbanion, which then combines with the positive carbon of the carbonyl group (reaction ii) the product regains a proton from the piperidinium ion, and then by loss of water followed by mono-decarboxylation of the malonic acid residue gives the final acid. [Pg.279]

Actually, the problem is clear. If all of you would stop taking amphetamines you would regain your fucking appetites Here s the recipes for when you get out of detox. [Pg.161]

Polymers that soften or melt and then solidify and regain their original properties on cooling are called thermoplastic. A thermoplastic polymer is usually a single strand of linear polymer with few if any cross-links. [Pg.1006]

If state n in Figure 2.2(a) is populated in excess of its Boltzmann population by absorption, the species M in this state will decay to the lower state until the Boltzmann population is regained. The decay is a first-order process, so that... [Pg.34]

Control of relative humidity is needed to maintain the strength, pHabiUty, and moisture regain of hygroscopic materials such as textiles and paper. Humidity control may also be required in some appHcations to reduce the effect of static electricity. Temperature and/or relative humidity may also have to be controlled in order to regulate the rate of chemical or biochemical reactions, such as the drying of varnishes, the appHcation of sugar coatings, the preparation of synthetic fibers and other chemical compounds, or the fermentation of yeast. [Pg.357]

Fig. 7. Moisture regains of cellulose acetate (A) and triacetate (T) fibers. Moisture content on a bone-dry basis, measured at 22°C (—... Fig. 7. Moisture regains of cellulose acetate (A) and triacetate (T) fibers. Moisture content on a bone-dry basis, measured at 22°C (—...
Polymer Standard tenacity, GPa Breaking elongation, % Modulus, GPa Density, kg/m Moisture. c regain... [Pg.312]

Among the bast textile fibers, the density is close to 1.5 g/cm, or that of cellulose itself, and they are denser than polyester, as shown iu Table 5. Moisture regain (absorbency) is highest iu jute at 14%, whereas that of polyester is below 1%. The bast fibers are typically low iu elongation and recovery from stretch. Ramie fiber has a particularly high fiber length/width ratio. [Pg.360]

To examine the soUd as it approaches equUibrium (atom energies of 0.025 eV) requires molecular dynamic simulations. Molecular dynamic (MD) simulations foUow the spatial and temporal evolution of atoms in a cascade as the atoms regain thermal equiUbrium in about 10 ps. By use of MD, one can foUow the physical and chemical effects that induence the final cascade state. Molecular dynamics have been used to study a variety of cascade phenomena. These include defect evolution, recombination dynamics, Hquid-like core effects, and final defect states. MD programs have also been used to model sputtering processes. [Pg.397]

Fiber type Breaking tenacity, N / tex Elongation, % Specific gravity Moisture regain, % Approximate melt point, °C... [Pg.163]

Concentrations of LCMs are 14—143 kg/m (5—50 Ib/bbl). The higher concentrations are used in the form of a 10—20 m (60—120 bbl) pill that is placed across the loss zone until a seal is estabhshed that allows circulation to be regained. [Pg.183]

The second process to finish phthalocyanine, which is more important for P-copper phthalocyanine, involves grinding the dry or aqueous form in a ball mill or a kneader (64). Agents such as sodium chloride, which have to be removed by boiling with water after the grinding, are used. Solvents like aromatic hydrocarbons, xylene, nitrobenzene or chlorobenzene, alcohols, ketones, or esters can be used (1). In the absence of a solvent, the cmde P-phthalocyanine is converted to the a-form (57,65) and has to be treated with a solvent to regain the P-modification. The aggregate stmcture also has an impact on the dispersion behavior of a- and P-copper phthalocyanine pigments (66). [Pg.505]


See other pages where Regaine is mentioned: [Pg.385]    [Pg.403]    [Pg.2108]    [Pg.142]    [Pg.401]    [Pg.88]    [Pg.243]    [Pg.251]    [Pg.252]    [Pg.320]    [Pg.15]    [Pg.206]    [Pg.362]    [Pg.363]    [Pg.363]    [Pg.268]    [Pg.275]    [Pg.275]    [Pg.277]    [Pg.293]    [Pg.341]    [Pg.341]    [Pg.353]    [Pg.360]    [Pg.378]    [Pg.488]    [Pg.67]    [Pg.72]    [Pg.436]    [Pg.148]    [Pg.291]    [Pg.320]    [Pg.183]    [Pg.223]    [Pg.236]    [Pg.236]    [Pg.236]   
See also in sourсe #XX -- [ Pg.17 , Pg.18 ]




SEARCH



Fiber regain

Fibre properties moisture regain

MOISTURE REGAIN

Moisture regain curve

Moisture regain, definition

Regain

Regain, defined

Regain, trade name

Regains

Solvent regain

Standard regains

Static regain

Water regain

Water regain value

Water regain volume

Water vapor regained

Weight loss/regain

© 2024 chempedia.info