Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Presentation mechanism

Used to present mechanical-type details to piping and mechanical vessel designers, electrical engineers, instrument engineers, and other engineers not directly in need of process details. This sheet contains pipe sizes, all valves (sizes and types), temperature points, and special details needed to insure a common working basis for all persons on a project. In some engineering systems. [Pg.5]

The present mechanism is being applied only to reactions involving good leaving groups. In these reactions the intermediates, VI and VIII, collapse to products much more rapidly than they return to starting materials. These are, therefore, reactions in which conditions (32) and (33)... [Pg.427]

Poly(f -caprolactone) (PCL), the most representative member of this polyester family, is obtained by the ring-opening polymerization of e-caprolactone. It is a low-7 (60°C), low-Tg (—60°C) semicrystalline polyester that presents mechanical properties resembling those of low-density polyethylene (Table 2.10). [Pg.43]

Scheme 6.2). In the previous mechanism, B was formed in concert with electron transfer, whereas the present mechanism follows the stepwise pathway. (The stepwise vs. concerted dichotomy is discussed in detail in Chapter 3 for the cased where the B —> B step is a bond-breaking reaction.) Although equation (6.51) still applies, equation (6.58) is replaced by... [Pg.402]

Wedge test results suggest that the curing process (e.g., percent crosslinking) of the epoxy-polyamide primer system is not affected by the addition of organosilanes, but may be affected by NTMP. The results of substrate surface characterization, adsorption behavior of applied films, and evaluation of candidate inhibitors by chemical, mechanical, and electrochemical test methods are presented. Mechanisms to explain the observed behavior of the various phosphonate and silane polymer systems are discussed. [Pg.234]

Molecular diffusion is a process in which chemical species move from regions of high concentration to regions of low concentration by Brownian motion. The rate of movement is directly proportional to the concentration gradient, normal to the direction of movement. Distribution of chemicals in the near surface and subsurface is not uniform, so that molecular diffusion is an ever-present mechanism. [Pg.220]

Ferruginous, coarse Pb-rich Bengaccah anomaly material would have been deposited over a relatively short interval in a palaeochannel and subsequently covered by later depositional material. However fermginous material (commonly pisoiiths) in the current stream channels reflects material transported and reworked over the period since the Tertiary. Thus the anomalous Pb in surficial coarse and magnetic soil fractions from the Bengaccah and Northern Pods area represents Tertiary to present mechanical dispersion. [Pg.89]

The results obtained by the present mechanical measurements are also consistent with the previous experimental results of the dynamic light scattering studies of the collective diffusion coefficient of gels and the rheological studies of the shear modulus of gels. The studies published by different researchers indicate that the concentration dependence of the collective diffusion constant of the polymer networks of gel and that of the elastic modulus are well represented by the following power law relationships [2, 3, 5]... [Pg.39]

The presented mechanisms are not the only ones occurring. Air bubbles or oil drops in water, for instance, are negatively charged, probably due to an adsorption of hydroxyl ions. The process is far from being understood. Many polymer surfaces acquire a negative surface charge in water. This could be due to anions, which are adsorbed due to the van der Waals force. Again, this process is not well understood. [Pg.61]

If a small-diameter pipe is used, the heat transfer area per unit of coil volume will be large. However, the pressure drop through the coil will be large unless multiple parallel passes are used. Parallel passes can present flow distribution problems. Small-diameter tubes also present mechanical strength problems. [Pg.45]

During the tests, the stack and SRU were instrumented to record voltage on each cell and to measure temperatures at different positions to highlight thermal gradients if present. Mechanical load was applied through weights external to the furnace. The load level was adapted to the stack/SRU design. [Pg.121]

These first two mechanical methods of breaking down wood into pulp provide the bases for all of the further developments in the field of mechanical pulping. While all of the present mechanical pulping methods do produce different types of pulp, they still rely upon either... [Pg.452]

The only difference between the present mechanism and the mechanisms to which it was compared is that the couplings of the organozinc compounds in Figure 16.25—just like some Pd-catalyzed C,C coupling reactions between organotin compounds and arylating or alkeny-... [Pg.714]

The interstitial mechanism is fundamentally seen in solute atoms which, as was previously stated, are smaller than the solvent atoms in binary interstitial alloys. Then, in the present mechanism... [Pg.231]

Mechanisms are the key to understanding the reactions of organic chemistry. For this reason, great care has been given to present mechanisms in a detailed, step-by-step fashion. The list below indicates when each mechanism in the text is presented for the first time. [Pg.1276]

The present paper reviews and assesses the current information about the formation and identification of X , AZ , and other doubly-charged negative ion species that have been reported. It also presents mechanisms and explanations for the production of the monatomic, diatomic and polyatomic doubly-charged negative ions that have been observed. Finally, some potentially fruitful paths for the further study of these ions are indicated. [Pg.91]

CAMEO II s Presentation Mechanism. The nature of HyperCard is essential to the effectiveness of CAMEO II and the Citizen s Helper. HyperCard allows users to choose among many different paths through a collection of information that may include graphics and fairly sophisticated computations as well as standard text. [Pg.116]

Table 2 presents mechanical properties of alloys with a matrix on the base of solid solution of niobium and molybdenum, dispersion-strengthened with chemical compounds, and also alloy with an additional frame strengthening owing to eutectoid TiFe. [Pg.418]


See other pages where Presentation mechanism is mentioned: [Pg.1077]    [Pg.45]    [Pg.95]    [Pg.637]    [Pg.31]    [Pg.175]    [Pg.136]    [Pg.38]    [Pg.380]    [Pg.161]    [Pg.254]    [Pg.300]    [Pg.257]    [Pg.535]    [Pg.11]    [Pg.355]    [Pg.272]    [Pg.900]    [Pg.48]    [Pg.25]    [Pg.222]    [Pg.203]    [Pg.2027]    [Pg.270]    [Pg.272]    [Pg.1245]    [Pg.243]    [Pg.2488]    [Pg.637]    [Pg.117]    [Pg.637]   
See also in sourсe #XX -- [ Pg.110 ]




SEARCH



© 2024 chempedia.info