Polystyrenes brominated, prepared

Preparation of Macromolecular Dioxolenium Salts. Living polystyrene prepared by the polymerization of styrene in THF with a-methylstyrene tetramer dianion reacted with a 2.1-molar amount of ethylene oxide for three hours at room temperature a 6.6-molar amount of adipoyl chloride was added, and the mixture was stirred for 20 horns a 20-molar amount of ethylenebromohydrin was added. This mixture was stirred for 44 hours. The bromoethylated polystyrene was precipitated in excess methanol and freeze-dried from benzene in a vacuum system. A 1-nitropropane solution of polystyrene dioxolenium salt was prepared by reaction of bromoethylated polystyrene with silver perchlorate in 1-nitropropane. Silver bromide was removed from the reaction mixture by filtration. Molecular weight of the product was measured by a vapor-pressure osmometer it was 1910 for living polystyrene and 5190 for the bromoethylated polystyrene. Bromine analysis of the bromoethylated polystyrene showed 67.9% of the calculated value. 

Poly(dibromostyrene). Poly(dibromostyrene) [62354-98-7] (PDBS) is prepared by the polymerization of dibromostyrene [31780-26-4] (50). Two versions are avaHable. One has a molecular weight of about 10,000, the other a molecular weight of about 80,000. Information comparing the performance of these materials to the performance of the brominated polystyrenes is not avaHable. 

Amos prepared his polymer-supported reagent in two steps from commercially available polystyrene beads (bromination, then condensation with lithium diphenylphosphide). He found that a useful range of sulphoxides could be reduced effectively, in good yields and in a few hours, to give clean samples of sulphides. 

Polystyrene/polyethylene oxide dendrimers were prepared by ATRP using tri- and tetra (bromomethyl) benzene as the initiators [207]. Each bromine end-group of the resulting stars was transformed first to two - OH groups and subsequently to potassium alcholate, as shown in Scheme 114. These - OK sites served to initiate the anionic polymerization of EO. The synthesized dendritic copolymers were found to display monomodal and narrow molecular weight distribution. 

These results indicate that if polydienes and similar polymers can be prepared quantitatively with tertiary amine terminal groups, then they can be combined with other halogen functional polymers using established techniques to create interesting new block copolymer systems. For example, consider the reaction between telechelic pyridine terminated polybutadiene and monofunctional bromine terminated polystyrene (equation 4) -the latter has been prepared in 95% yield. >it The product would be an ABA... 

Nickel(II) catalysts with a direct nickel(II)-polystyrene bond have been prepared by oxidative addition of tetrakis(triphenylphosphine) nickel(O) to brominated polystyrene (58) ... 

Alternatively, boranes can be prepared in solution and then coupled with support-bound carbon electrophiles. The Suzuki coupling of alkylboranes, generated in situ from 9-BBN and alkenes, with brominated cross-linked polystyrene has been used to link substituted alkyl chains directly to the polymer (Entry 4, Table 5.3). Alkylboranes have also been used to alkylate polystyrene-bound aryl iodides (Entries 3 and 5, Table 5.3). 

A sample of polystyrene prepared by heating styrene with tribromobenzoyl peroxide in the absence of air has the formula Br3C6H3(C jHg)w. The number n varies with the conditions of preparation. One sample of polystyrene prepared in this manner was found to contain 10.46% bromine. What is the value of n ... 

A similar well-defined graft copolymer consisting of polystyrene main chain and branches (G-7) can be prepared simply via repetition of copper-catalyzed living radical polymerizations.209 Thus, the synthesis starts with the copolymerization of styrene and />(acetoxymethy 1)styrene or />(methoxymethyl)sty-rene, followed by bromination of the substituent into the benzyl bromide moiety, which then initiates the copper-catalyzed radical polymerization of styrene to give graft polymers with 8—14 branches. 

Polymer-supported Wittig reagents were first prepared more than 20 years ago [32]. It has been shown that the success of the reaction depends strongly upon (i) the preparation of the reagent by bromination and phosphination of cross-linked polystyrene rather than by co-polymerization using styryldi-phenyl phosphine, and (ii) the generation of the phosphorane with a base/ solvent system that swells the phosphonium sites in the polymer network (Scheme 6) [33]. Thus, bromination of polystyrene 1 yielded phenyl bromide 32, and this was followed by phosphination with n-butyUithium and chlor-odiphenylphosphine or with Hthium diphenylphosphide to give 33, a compound which is commercially available (Scheme 6). 

Polymeric reagent. Hodge and Richardson have prepared a polymer-supported triphenylphosphine by bromination of a polystyrene cross-linked with divinylbenzene followed by reaction with lithium diphenylphosphide (4, 303). A similar reagent has been described by Regen and Lee. Polymeric material is available from Strem. 

---