Polyolefins polyolefin foams

There are three basic types of polyethylene foams of importance (/) extmded foams from low density polyethylene (LPDE) (2) foam products from high density polyethylene (HDPE) and (J) cross-linked polyethylene foams. Other polyolefin foams have an insignificant volume as compared to polyethylene foams and most of their uses are as resia extenders. 

Rodriguez-Perez, M. A. Crosslinked Polyolefin Foams Production, Structure, Properties, and Applications. Vol. 184, pp. 97-126. 

Polyolefin Foams, N.J. Mills, Metallurgy and Materials, University of Birmingham. 

In the manufacturing of crosslinked polyolefin foam, the foam expansion and cell stabilization highly dependent on the degree of crosslinking. It has been reported that at higher crosslinking level the foam produce have higher density [1, 2]. 

Olefins or alkenes are defined as unsaturated aliphatic hydrocarbons. Ethylene and propylene are the main monomers for polyolefin foams, but dienes such as polyisoprene should also be included. The copolymers of ethylene and propylene (PP) will be included, but not polyvinyl chloride (PVC), which is usually treated as a separate polymer class. The majority of these foams have densities <100 kg m, and their microstructure consists of closed, polygonal cells with thin faces (Figure la). The review will not consider structural foam injection mouldings of PP, which have solid skins and cores of density in the range 400 to 700 kg m, and have distinct production methods and properties (456). The microstructure of these foams consists of isolated gas bubbles, often elongated by the flow of thermoplastic. However, elastomeric and microcellular foams of relative density in the range 0.3 to 0.5, which also have isolated spherical bubbles (Figure lb), will be included. The relative density of a foam is defined as the foam density divided by the polymer density. It is the inverse of the expansion ratio . 

Denning s three papers in the late 1960s (a.2-a.4) reviewed the development of closed-cell polyolefin foams, and their mechanical properties. Some of his predictions on materials development turned out to be true. In Part I he explains that non-crosslinked polyethylene (PE) foams have inferior creep properties to crosslinked foams this appeared to be the tensile creep of the melt, rather than compressive creep of the... 

Polyolefin foams are easier to model than polyurethane (PU) foams, since the polymer mechanical properties does not change with foam density. An increase in water content decreases the density of PU foams, but increases the hard block content of the PU, hence increasing its Young s modulus. However, the microstructure of semi-crystalline PE and PP in foams is not spherulitic, as in bulk mouldings. Rodriguez-Perez and co-workers (20) showed that the cell faces in PE foams contain oriented crystals. Consequently, their properties are anisotropic. Mechanical data for PE or PP injection mouldings should not be used for modelling foam properties. Ideally the mechanical properties of the PE/PP in the cell faces should be measured. However, as such data is not available, it is possible to use data for blown PE film, since this is also biaxially stretched, and the texture of the crystalline orientation is known to be similar to that in foam faces. 

Harden s (27) market survey of the growth of polyolefin foams production and sales shows that 114 x 10 kg of PE was used to make PE foam in 2001. The growth rate for the next 6 years was predicted as 5-6% per year, due to recovery in the US economy and to penetration of the automotive sector. In North America, 50% of the demand was for uncrosslinked foam, 24% for crosslinked PE foams, 15% for EPP, 6% for PP foams, 3% for EVA foams and 2% for polyethylene bead (EPE) foam. As protective packaging is the largest PE foam use sector, PE foam competes with a number of other packaging materials. Substitution of bead foam products (EPP, EPE, ARCEL copolymer) by extruded non-crosslinked PE foams, produced by the metallocene process was expected on the grounds of reduced costs. Compared with EPS foams the polyolefin foams have a lower yield stress for a given density. Compared with PU foams, the upper use temperature of polyolefin foams tends to be lower. Eor both these reasons, these foams are likely to coexist. 

MELT STRENGTH ANALYSIS FOR EXTRUDED POLYOLEFIN FOAM DEVELOPMENT... 

Houston, Tx., 25th-28th Eeb. 2001, p.431-40 MUCELLTHERMOFORMABLE POLYOLEFIN FOAM SHEET Blizard K Chapman B Trexel Inc. 

CROSSLINKING OF POLYOLEFIN FOAMS. I. EFFECT OF TRIALLYL CYANURATE ON DICUMYL PEROXIDE CROSSLINKING OF LOW-DENSITY POLYETHYLENE... 

---