Polymers activation energy

Polymer Activation energy Frequency factor E kcal/mol A s Rale at 350 C weight %/min. 

Since in snch polymers activation energy barriers for diffusion are low, the prevailing effects are exerted by negative AH valnes. The temperature dependence of the permeability coefficients in PTMSN shows that such behaviour is typical also for this polymer... 

Polymer Activation energy Qo (kJ moE ) Activation volume a, Volume of monomer unit V, Number of monomer units m = ajV qi = Qo/m (kJ moE ) -Ecoh/3 tk.T moEh... 

Polymer Activation Energy kJ/mol Polymer Activation Energy kJ/mol... 

Fig. 23. Representative protecting groups for phenolic and carboxylic acid-based systems, (a) The polymer-based protecting groups are fisted in order of increasing activation energy for acid-catalyzed deprotection, (b) Acid-labile monomeric dissolution inhibitors, a bifunctional system based on protected bisphenol A. (c) Another system that combines the function of dissolution inhibitor and PAG in a single unit.

Melt Viscosity. As shown in Tables 2 and 3, the melt viscosity of an acid copolymer increases dramatically as the fraction of neutralization is increased. The relationship for sodium ionomers is shown in Figure 4 (6). Melt viscosities for a series of sodium ionomers derived from an ethylene—3.5 mol % methacrylic acid polymer show that the increase is most pronounced at low shear rates and that the ionomers become increasingly non-Newtonian with increasing neutralization (9). The activation energy for viscous flow has been reported to be somewhat higher in ionomers than in related acidic... 

The Arrhenius relationship (eq. 5) for crystalline polymers or other transitions, where E is the activation energy and R the gas constant (8.3 J/mol), is as follows ... 

Polymerization Solvent. Sulfolane can be used alone or in combination with a cosolvent as a polymerization solvent for polyureas, polysulfones, polysUoxanes, polyether polyols, polybenzimidazoles, polyphenylene ethers, poly(l,4-benzamide) (poly(imino-l,4-phenylenecarbonyl)), sUylated poly(amides), poly(arylene ether ketones), polythioamides, and poly(vinylnaphthalene/fumaronitrile) initiated by laser (134—144). Advantages of using sulfolane as a polymerization solvent include increased polymerization rate, ease of polymer purification, better solubilizing characteristics, and improved thermal stabUity. The increased polymerization rate has been attributed not only to an increase in the reaction temperature because of the higher boiling point of sulfolane, but also to a decrease in the activation energy of polymerization as a result of the contribution from the sulfonic group of the solvent. 

Crystallization kinetics have been studied by differential thermal analysis (92,94,95). The heat of fusion of the crystalline phase is approximately 96 kj/kg (23 kcal/mol), and the activation energy for crystallization is 104 kj/mol (25 kcal/mol). The extent of crystallinity may be calculated from the density of amorphous polymer (d = 1.23), and the crystalline density (d = 1.35). Using this method, polymer prepared at —40° C melts at 73°C and is 38% crystalline. Polymer made at +40° C melts at 45°C and is about 12% crystalline. 

In general, the activation energies for both cationic and anionic polymerization are small. For this reason, low-temperature conditions are normally used to reduce side reactions. Low temperatures also minimize chain transfer reactions. These reactions produce low-molecular weight polymers by disproportionation of the propagating polymer ... 

T. See Temperature Tail-to-tail polymer, 613 Teflon, 614 Temperature (T), 7 activation energy and, 302 calculation of, 109 critical, 231-222... 

In molecular doped polymers the variance of the disorder potential that follows from a plot of In p versus T 2 is typically 0.1 eV, comprising contributions from the interaction of a charge carrier with induced as well as with permanent dipoles [64-66]. In molecules that suffer a major structural relaxation after removal or addition of an electron, the polaron contribution to the activation energy has to be taken into account in addition to the (temperature-dependent) disorder effect. In the weak-field limit it gives rise to an extra Boltzmann factor in the expression for p(T). More generally, Marcus-type rates may have to be invoked for the elementary jump process [67]. 

---