Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Plastic history

J. H. Dubois, Plastics History USA, Cahners Books, Boston, 1975. [Pg.23]

Hyatt, John Wesley (1837-1920) During the 1860s John Wesley Hyatt developed cellulose nitrate plastic and successfully produced and marketed billiard balls as a less expensive alternative to ivory billiard balls. See cellulose nitrate plastic plastic history. [Pg.305]

J.H. DuBois, "Plastics History USA," Cahner Books, Boston, MA, 1972. [Pg.13]

Chemists—Biography. 2. Polymers—History. 3. Plastics--History. I. Seymour, Raymond Benedict, 1912-. II. Series. [Pg.276]

J.H. DuBois, Plastics History U.S.A. (Cashners Books, Boston 1972). [Pg.114]

DuBois JH. Plastics history USA. Boston, MA Cahners Books 1972. [Pg.376]

Although the use of simple diluents and adulterants almost certainly predates recorded history, the use of fillers to modify the properties of a composition can be traced as far back as eady Roman times, when artisans used ground marble in lime plaster, frescoes, and po22olanic mortar. The use of fillers in paper and paper coatings made its appearance in the mid-nineteenth century. Functional fillers, which introduce new properties into a composition rather than modify pre-existing properties, were commercially developed eady in the twentieth century when Goodrich added carbon black to mbber and Baekeland formulated phenol— formaldehyde plastics with wood dour. [Pg.366]

Polymer Composition. The piopeities of foamed plastics aie influenced both by the foam stmctuie and, to a gieatei extent, by the piopeities of the parent polymer. The polymer phase description must include the additives present in that phase as well. The condition or state of the polymer phase (orientation, crystallinity, previous thermal history), as well as its chemical composition, determines the properties of that phase. The polymer state and cell geometry are intimately related because they are determined by common forces exerted during the expansion and stabilization of the foam. [Pg.411]

The first polymer with a polymethylene stmcture was synthesized by von Pechmann in 1898 from diazomethane (1). Since then, there have been four milestones in the history of PE polymers as commercial plastics. [Pg.367]

Phthalocyanine pigments account for approximately 23% of the total worldwide organic pigment consumption of 225,000 tons. Approximately 20,000 t are used in printing inks, 10,000 t in paints, 9,000 t in plastics, 3,000 t in textiles, 7,000 t in dyes, and 2,000 t in specialty uses. Table 1 shows the worldwide distribution of cmde phthalocyanine capacity. The production history of phthalocyanine in the United States from 1980 to 1990 is given in Table 2 (161). The 1990 prices of phthalocyanine blue and green pigments were ca 11—22/kg and 21—27/kg, respectively. [Pg.507]

PS Foams. The eady history of foamed PS is available (244), as are discussions of the theory of plastic foams (245). Foamable PS beads were developed in the 1950s by BASF under the trademark of STYROPOR (246—248). These beads, made by suspension polymerization in the presence of blowing agents such as pentane or hexane, or by post-pressurization with the same blowing agents, have had an almost explosive growth, with 200,000 metric tons used in 1980. Some typical physical properties of PS foams are Hsted in Table 10 (see Foamed plastics). [Pg.526]

A crystalline or semicrystalline state in polymers can be induced by thermal changes from a melt or from a glass, by strain, by organic vapors, or by Hquid solvents (40). Polymer crystallization can also be induced by compressed (or supercritical) gases, such as CO2 (41). The plasticization of a polymer by CO2 can increase the polymer segmental motions so that crystallization is kinetically possible. Because the amount of gas (or fluid) sorbed into the polymer is a dkect function of the pressure, the rate and extent of crystallization may be controUed by controlling the supercritical fluid pressure. As a result of this abiHty to induce crystallization, a history effect may be introduced into polymers. This can be an important consideration for polymer processing and gas permeation membranes. [Pg.223]

It may well be argued that the history of polystyrene is more closely bound up with the history of the 20th century than is the case with any other plastics material. [Pg.425]


See other pages where Plastic history is mentioned: [Pg.292]    [Pg.304]    [Pg.409]    [Pg.412]    [Pg.428]    [Pg.461]    [Pg.475]    [Pg.514]    [Pg.292]    [Pg.304]    [Pg.409]    [Pg.412]    [Pg.428]    [Pg.461]    [Pg.475]    [Pg.514]    [Pg.262]    [Pg.252]    [Pg.443]    [Pg.110]    [Pg.182]    [Pg.306]    [Pg.97]    [Pg.223]    [Pg.295]    [Pg.495]    [Pg.69]    [Pg.146]    [Pg.324]    [Pg.150]    [Pg.3]    [Pg.4]    [Pg.930]    [Pg.936]    [Pg.941]    [Pg.110]    [Pg.123]    [Pg.201]    [Pg.359]    [Pg.359]    [Pg.361]   
See also in sourсe #XX -- [ Pg.138 ]




SEARCH



A Brief History of Bio-Based Plastics

A Brief History of Natural and Synthetic Plastic Materials

BASFs History in Plastics

Foamed plastics history

History of Biodegradable Plastics

History of Plastic (Virgin, Recycled)

Plastic deformation history, effect

Plastics 366 heat history

© 2024 chempedia.info