Overpotential coefficients

Tjo = Overpotential coefficient or drainage overpotential (10 Re = Longitudinal resistance of the structure (ohm/cm)... 

The usual Tafel evaluation yielded a transfer coefficient a = 0.52 and a rate constant k of 4x 10 cm s at the standard potential of the MV /MV couple. This k value corresponds to a moderately fast electrochemical reaction. In this electrode-kinetic treatment the changes in the rate of electron transfer with pH were attributed only to the changes in the overpotential. A more exact treatment should also take into account the electrostatic effect on the rate of reaction which also changes with pH. 

Both the frequency of the well and its depth cancel, so that the free energy of activation is determined by the height of the maximum in the potential of mean force. The height of this maximum varies with the applied overpotential (see Fig. 13). To a first approximation this dependence is linear, and a Butler-Volmer type relation should hold over a limited range of potentials. Explicit model calculation gives transfer coefficients between zero and unity there is no reason why they should be close to 1/2. For large overpotentials the barrier disappears, and the rate will then be determined by ion transport. 

In order to obtain a definite breakthrough of current across an electrode, a potential in excess of its equilibrium potential must be applied any such excess potential is called an overpotential. If it concerns an ideal polarizable electrode, i.e., an electrode whose surface acts as an ideal catalyst in the electrolytic process, then the overpotential can be considered merely as a diffusion overpotential (nD) and yields (cf., Section 3.1) a real diffusion current. Often, however, the electrode surface is not ideal, which means that the purely chemical reaction concerned has a free enthalpy barrier especially at low current density, where the ion diffusion control of the electrolytic conversion becomes less pronounced, the thermal activation energy (AG°) plays an appreciable role, so that, once the activated complex is reached at the maximum of the enthalpy barrier, only a fraction a (the transfer coefficient) of the electrical energy difference nF(E ml - E ) = nFtjt is used for conversion. 

Fig. 5.2 Dependence of the relative current density j/j0 on the overpotential rj according to Eq. (5.2.28). Various values of the charge transfer coefficient a are indicated at each curve. Dashed curves indicate the partial current densities (Eqs 5.2.11 and 5.2.12 for a = 0.5). (According to K. Vetter)...

In the first case, the rate of deposition depends on the equilibrium concentration of ad-atoms, on their diffusion coefficient, on the exchange current density and on the overpotential. In the second case, the rate of deposition is a function, besides of the geometric factors of the surface, of the exchange current and the overpotential. This mechanism is valid, for example, in the deposition of silver from a AgN03 solution. 

The reorganization free energy /.R represents the electronic-vibrational coupling, ( and y are fractions of the overpotential r] and of the bias voltage bias at the site of the redox center, e is the elementary charge, kB the Boltzmann constant, and coeff a characteristic nuclear vibration frequency, k and p represent, respectively, the microscopic transmission coefficient and the density of electronic levels in the metal leads, which are assumed to be identical for both the reduction and the oxidation of the intermediate redox group. Tmax and r max are the current and the overvoltage at the maximum. 

Consider the reaction with two consecutive electron-transfer steps described by Eq. (11.12). (a) Show that, if j0,2 j0,1, there is an intermediate range of negative overpotentials in which the apparent transfer coefficient is (2 — ai) and the apparent exchange current density 2j0,i (see Fig. 11.1). (b) Derive the form of the Tafel plot for jo,i > jo,2-... 

The effect of overpotential on the transition state relative to the reactant and product states can be determined by the transfer coefficients, aA and ac, where... 

Tafel s equation (eqn (30)) is accurate at large overpotentials, but fails as q approaches zero. The Tafel plot is obtained by plotting rj vs. log i, with b referred to as the Tafel slope. The Tafel slope is a function of the transfer coefficients and temperature, where... 

Figure 7.12 Schematic Tafel plot of log / (as y ) against overpotential rj (as x ). The linear regions yield the Tafel slopes, from which the transfer coefficients a can be determined. The intersection between the two Tafel regions occurs on the y-axis at log /o. ...

In a PEMFC, the power density and efficiency are limited by three major factors (1) the ohmic overpotential mainly due to the membrane resistance, (2) the activation overpotential due to slow oxygen reduchon reaction at the electrode/membrane interface, and (3) the concentration overpotential due to mass-transport limitations of oxygen to the electrode surfaced Studies of the solubility and concentration of oxygen in different perfluorinated membrane materials show that the oxygen solubility is enhanced in the fluorocarbon (hydrophobic)-rich zones and hence increases with the hydrophobicity of the membrane. The diffusion coefficient is directly related to the water content of the membrane and is thereby enhanced in membranes containing high water content the result indicates that the aqueous phase is predominantly involved in the diffusion pathway. ... 

Figure 5. Measurement and analysis of steady-state i— V characteristics, (a) Following subtraction of ohmic losses (determined from impedance or current-interrupt measurements), the electrode overpotential rj is plotted vs ln(i). For systems governed by classic electrochemical kinetics, the slope at high overpotential yields anodic and cathodic transfer coefficients (Ua and aj while the intercept yields the exchange current density (i o). These parameters can be used in an empirical rate expression for the kinetics (Butler—Volmer equation) or related to more specific parameters associated with individual reaction steps.(b) Example of Mn(IV) reduction to Mn(III) at a Pt electrode in 7.5 M H2SO4 solution at 25 Below limiting current the system obeys Tafel kinetics with Ua 1/4. Data are from ref 363. (Reprinted with permission from ref 362. Copyright 2001 John Wiley Sons.)...

---