Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Mold flow

Molding is the process where a pattern is pressed or embedded into special sand to the desired shape or form. Alternatively, the pattern can be placed on a molding board, and the sand rammed or compressed around the pattern. Figure 4.4 shows the typical molding flow. The sand and binder are first... [Pg.153]

Figure 11. Maximum low temperature loss tangent (35 Hz) measured normal to mold flow vs. styrene block length heterogeneity. Circles— branched polymers, triangles—linear polymers, solid symbols—electron micrographs displayed. Figure 11. Maximum low temperature loss tangent (35 Hz) measured normal to mold flow vs. styrene block length heterogeneity. Circles— branched polymers, triangles—linear polymers, solid symbols—electron micrographs displayed.
Dispersing agent and accelerator activator in rubber compounds. It aids dispersion of pigments and fillers and improves processing since it acts as a stock lubricant and can facilitate mold flow, improve extrusions and aid release. [Pg.312]

The outermost element of the unit cell (Figs 1 and 2) is the current collector plate, which typically contains a machined or molded gas flow field. These two functions of current collector and gas flow field may be fulfilled, in principle, by two separate components however, in most of the cells and stacks built to date, the flow field is introduced as part of the current collector fabrication process. A current collector plate, with machined or molded flow field on each of its sides, becomes the... [Pg.552]

MoldPro. [Witco/Humko] Oko f deriv. internally fiinctiona] processing agents to improve mold flow, mold release, and extrusion of elastomeric oompds. [Pg.236]

Backrinding Appearance Shrinkage Cured hardness Porosity Mold release Mold fouling Mold flow/fill... [Pg.199]

MED mold-flow direction MMC metal matrix composite... [Pg.602]

Chem. Descrip. Syn. wax CAS 8002-74-2 EINECS/ELINCS 232-315-6 Uses Wax for hot-melt adhesives, inks, paints/coatings, textiles, plastics lubrication, color concentrates, and additive to wax blends vise, reducer mold flow improver improves filler disp. and metal release Features Inc. extrusion rates Properties Vise. 10 cps (250 F) congeal, pt. 208 F Paraflint Spray 20 [Moore Munger]... [Pg.605]


See other pages where Mold flow is mentioned: [Pg.369]    [Pg.603]    [Pg.144]    [Pg.649]    [Pg.1047]    [Pg.154]    [Pg.20]    [Pg.18]    [Pg.193]    [Pg.759]    [Pg.766]    [Pg.816]    [Pg.279]    [Pg.280]    [Pg.486]    [Pg.331]    [Pg.110]    [Pg.237]    [Pg.2617]    [Pg.2618]    [Pg.3033]    [Pg.408]    [Pg.61]    [Pg.286]    [Pg.333]    [Pg.369]    [Pg.371]    [Pg.376]    [Pg.433]    [Pg.461]    [Pg.561]    [Pg.745]    [Pg.328]    [Pg.328]   
See also in sourсe #XX -- [ Pg.283 ]

See also in sourсe #XX -- [ Pg.58 ]




SEARCH



Analysis mold flow

Casting flow molding

Compression molding squeezing flow

Design-mold basics of flow

Flow molding

Flow molding process

Flow molding technique

Injection Molding - Isothermal Flow Problems

Injection mold resin flow

Injection molding fountain flow

Injection molding melt flow

Injection molding melt-flow oscillation

Melt flow injection molding, influence

Melt flow molding

Melt flow oscillation molding

Mesa flow mold

Mold filling fountain flow

Mold-cavity melt fountain flow

Mold-cavity melt-flow analysis

Mold-cooling flow meter

Mold-flow direction

Molding flow chart

Plastic product design flow molding

Reaction injection molding melt flow

Resin flow molding

Rotational molding high-flow plastics

Spiral mold flow

Thin section moldings, flow

© 2024 chempedia.info