Minimum equipment

Client s Inspector will check, as a minimum, equipment components, dimensions, connection sizes and locations, and quality of workmanship against certified drawings, data sheets, and purchase order documents. 

Maintenance Unavailability shift supervisor s logs and minimum equipment lists so unavailability of equipment needed to mitigate a shut-down accident. 

The diesel engine is the most dependable engine for driving fire water pumps and should be the only type of engine acceptable for this service. The following minimum equipment should be provided for diesel engines ... 

The purchase prices of Petro-Belt and Dyna-Belt hydrocarbon skimmers are shown in Table 1. The minimum equipment required includes a skimmer, a belt, and a drum. For well applications in groundwater, the endurathane belt is to be used. This information is from a 1997 vendor brochure. 

N List of minimum equipment for efficient running of a pharmacy. 

Manufacturing Rooms Manufacturing rooms must be well designed in order to ensure adequate cleaning and reduction of cross-contamination. Points of dust accumulation like 90° angles areas must be avoided in the room, dust collectors or air lines must be presented restrictly at the wall surface and only the minimum equipments must be presented in a room. 

For minimum equipment cost, the work requirement should be the same for each stage. For ideal gases with no friction losses between stages, this implies equal compression ratios. With n... 

Confirm hydraulic calculations on all pump circuits and establish pump NPSH and minimum equipment elevations. 

Many OEMs include only the minimum equipment for lubrication as a part of the original bill-of-material. Anything else is optional and therefore frequently left out. While these options add to the cost, many generate real value when selected. Following is a list of lubrication-related hardware and accessories that, where suitable for a particular machine and application, could and should be factory-installed. If not, they will need to be retrofitted onsite. ... 

Liquid Flow Measurement. The requirement of accurate liquid flow measurement can also elevate process equipment (see Figure 7-8). If liquid is near the boiling point, a static head is required in the front of the control valve to overcome pipe friction losses and avoid flashing in the line. Minimum equipment elevation, orifice range and minimum line size can be used if the orifice is as close to the equipment as possible and the piping has only one elbow up to the control valve. 

ONE ELBOW IN PIPING GIVES MINIMUM PRESSURE DROP UP TO THE CONTROL VALVE AND MINIMUM EQUIPMENT HEIGHT. 

The main advantage of the technique lies in its simplicity and minimum equipment required. The extraction can even be done in the sample bottle if there is enough headspace for adequate mixing after adding the solvent. 

Refer to Section Cell Setup and Connections for Three- and Two-Electrode Configurations for a list of minimum equipment required. 

Equipment needed for microscopy in a cement plant may range from only a polarized-light microscope required for powder mount analysis to sawing, grinding, and polishing equipment necessary for thin-sec-tion and polished-section study. Two somewhat idealized lists of equipment are given in Table 11-1. The "Economy" column in the table contains only the minimum equipment for powder-mount study and polished-section examination. The other column also contains items for preparation of thin sections. 

A sound Minimum Equipment List (MEL) can be maintained and amended according to experience. 

Minimum Equipment required for dispatch of the aircraft. The regulatory authorities require that aU equipment installed on an aeroplane in compliance with the Type Certification Basis must be operative. Experience has proven that, due to the various levels of redundancy designed into an aeroplane, operation of every system or installed component may not be necessary when the remaining operative equipment satisfies the airworthiness authorities (ARPS 150, para 3.4.2). Therefore, certain conditional deviations from the original requirement are authorised to permit aeroplane dispatch. These Dispatch Deviations identity ... 

Master Minimum Equipment List A list of equipment and functions which need not be operative for safe flight and landing based on stated compensating precautions created during aeroplane type certification [ARPS 150]. 

Minimum Equipment List An approved list of items which may be inoperative for flight under specified conditions cooperatively created by operators and regulatory authorities [ARPSISO]. 

Two types of maintenance may be implemented when TLD is apphed. These are minimum equipment list (MEL) maintenance and periodic inspection and repair (PIR) maintenance (FAA Memo 2001). MEL maintenance is most commonly applied to STD faults and PIR maintenance is most commonly applied to LTD faults. However, there are no restrictions in place to this effect. 

Establishing and assessing a set of suitable criteria is considered the main activity of this selection problem. These criteria comprise the minimum equipment requirements relevant for the drilling jar selection, e.g. availability, manufacturer service agreements, documentation of earlier performance and specification of drilling jar sizes and material properties compatible to other assembly equipment planned used in the drilling operations. Based on these criteria the set of alternatives is reduced, and in many cases these criteria are decisive for the decision-making. 

Strength, up to 100% of parent matmals, easily and economically obtained with minimum equipment requirements. 

The ESF actuation system is composed of redundant trains A, B, C, and D. The instrumentation and controls of each train are physically and electrically separate and independent. The ESF actuation system can sustain the loss of an entire train and still provide its required protective action. Specific ESF design criteria are addressed for environmental and seismic equipment qualification, single failure criterion, and minimum equipment and system response times. 

The minimum equipment requirements for demonstration of simple electrospinning in the laboratory are as follows ... 

It has been our experience that the firefly luminescence system is a highly sensitive and specific tool for rapid submicro estimations of ATP and some related compounds (17). When used in conjunction with more classical methods as standards and checks (1,2,6-9), it has proved quite consistent and reproducible to about 5% accuracy for as little as 10 g. of labile ATP phosphorus. While for most purposes the luminescence assay for ATP is applicable and perhaps preferable to other methods, it is incumbent upon the reviewer to present additional methods for the use of those who do not have minimum equipment for the use of the firefly extract at hand or who prefer to use more classical methods routinely or for controls. 

The following minimum equipment must be supplied on all boats ... 

---