Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Mills continuous

Fig. 2.23 (a) Desorption kinetic curves at various temperatures under initial hydrogen pressure of 0.1 MPa of the commercial Tego Magnan MgH powder milled continuously for 20 h under the IMP68 mode in argon and (b) the Arrhenius plot of the desorption rate for the estimation of the apparent activation energy, E, using kinetics data for four temperatures 300, 325, 350, and 375°C -140... [Pg.115]

Fig. 2.25 DSC traces of Tego Magnan powder milled continuously for 20 (continuous line) and 100 h (broken line) under the IMP68 mode in argon (heating rate 4°C/min)... Fig. 2.25 DSC traces of Tego Magnan powder milled continuously for 20 (continuous line) and 100 h (broken line) under the IMP68 mode in argon (heating rate 4°C/min)...
Fig. 2.27 XRD patterns of MgH2 (Tego Magnan) powders milled continuously for 100 h under the IMP68 mode in argon and subsequently desorbed directly after milling in a Sieverts-type apparatus at various temperatures... Fig. 2.27 XRD patterns of MgH2 (Tego Magnan) powders milled continuously for 100 h under the IMP68 mode in argon and subsequently desorbed directly after milling in a Sieverts-type apparatus at various temperatures...
Fig. 3.2 (a) Evolution of the XRD patterns of 2Mg-Fe mixture reactively milled sequentially for various times under 1MP2 mode in 880 kPa of hydrogen. For comparison the XRD pattern of the mixture milled continuously for 270 h is also shown, (b) Morphology of 2Mg-Fe mixture reactively milled for 270 h in a continuous manner... [Pg.201]

Steel sheets, widely used in thousands of products, are produced Irorn slabs from a slabbing mill, continuous casting machine, or pressure-poured molils. These pieces are hot-rolled in a hoi strip mill, descaled bv pickling in an acid solution, and then cold-rolled and tempered m a cold-reduction and temper mill. Tlte cold-tolled snip may he marketed in coil form, or carried to a side-trimming and sheet shearing line, where it is customized lor speeilie user needs. [Pg.882]

The effect of ball milling is similar in all cases. Within the first 10 min of milling, the 002 reflection is considerably broadened and appears slightly shifted to a smaller angle. This apparent shift is probably the result of the superposition of the broadened 002 peak upon the rising, broad, amorphous peak which centers about 18.5° (2 ). As ball milling continues, the crystalline characteristics decrease and the amorphous characteristics increase. After about 1 hr of milling time, the crystalline characteristics of all the cellulosic materials have disappeared. [Pg.81]

Milling High-shear milling (Fitz milling) Continuous process... [Pg.652]

Colloid mill Continuous Laminar flow Moderate... [Pg.201]

Disk mill Continuous, rough grinding 150 kg/hour Hard. solids 0.1 mm minimum... [Pg.127]

Milled Glass Filler - Milled glass fdlers are made by hammer-milling continuous glass strands. Used as anticrazing reinforcing fdlers for adhesives and in plastics. Also called milled glass fiber. [Pg.534]

In the first step isothiocyanates were prepared by the procedure described above, and then without isolation 1 equiv. of second amine was added and milling continued. Upon completion, treatment of reaction mixture with aqueous hydrochloric add and filtration afforded unsymmetrical products in high yields (entries 10-13). [Pg.182]


See other pages where Mills continuous is mentioned: [Pg.633]    [Pg.633]    [Pg.633]    [Pg.57]    [Pg.41]    [Pg.116]    [Pg.118]    [Pg.120]    [Pg.200]    [Pg.248]    [Pg.700]    [Pg.277]    [Pg.115]    [Pg.116]    [Pg.118]    [Pg.120]    [Pg.200]    [Pg.248]    [Pg.6]    [Pg.97]    [Pg.1153]    [Pg.370]    [Pg.2293]    [Pg.2276]    [Pg.51]    [Pg.348]    [Pg.111]    [Pg.273]    [Pg.184]    [Pg.190]    [Pg.191]    [Pg.357]   
See also in sourсe #XX -- [ Pg.20 , Pg.21 , Pg.22 , Pg.23 , Pg.24 , Pg.25 , Pg.26 , Pg.27 , Pg.28 , Pg.29 , Pg.30 , Pg.31 ]




SEARCH



© 2024 chempedia.info