Medium density polyethylene

Noroozu and Zeboria [57] have measured the effect of multiwalled carbon nanotubes on the mechanical and thermal properties of medium-density polyethylene matrix carbon nanotube nanocomposites. 

Polyetheramide and epoxy resins Mechanical and electrical properties 50 

Incorporation of 0.5% to 5% of high-density polyethylene and multiwalled carbon nanotube composites improves Young s modulus from 0.4 to 0.56 GPa, yield stress from 16.34 to 19.02 MPa, and consumed energy up to 7% strain from 4729 to 

The following conclusions were reached in this work  

FIGURE 3.1 Electron micrograph of medium-density polyethylene before milling. 

---

Table 9 Metallocene-Based Medium-Density Polyethylene...

Hexane Permeation Predictions for Medium-Density Polyethylene (MDPE) Sheet Sample of Thickness 1.57 mm at 40°C... 

MDPE Medium-density polyethylene PMA Poly(methacrylate)... 

Medium color carbon blacks, 4 798t Medium density polyethylene (MDPE) resins, 77 700, 701... 

Figure 6. Weight change of medium density polyethylene as a function of time following immersion in 1,1,1-trichloroethane...

Figure 13. Concentration ( one a) of 1,2-dichloroethane in aqueous phase of cell as a function of time following challenge to medium density polyethylene...

P.J. Garrison, L.R. Wallace, D.L. Wise, J.H. Meas, Jr., L.V. Cribbs, J.A. Merrick-Mack, and P.L. Nygard, High molecular weight, medium density polyethylene, US Patent 6486270, assigned to Equistar Chemicals, LP (Houston, TX), November 26,2002. 

Its greatest deficiency is processability—it is hardly thermoplastic at all Hercules sells mill shapes which must be machined into 6nd products, while Formica has developed a continuous compactionsintering machine for producing it in sheet and laminate form (3). In addition, its modulus, strength, and heat distortion temperature are no better than conventional medium-density polyethylene. Bar, plate, and rod stock sell for 2 up, before machining. 

MDPE—Abbreviation used to denote medium density polyethylene. A type of plastic material used to make cable jacketing. 

In first developmental studies, containers were made with polyurethane. However, it was found (Ref 1) that medium density polyethylene is an ideal material to fabricate expl safety containers. Two different sizes of containers were developed by Zimmer Asaoka a 10-cm diameter container which can easily withstand the expln of 15g of NG and a 32-cm diameter 500g of NG, if small detonators (DuPont S 67 squib) are used. The smaller container weighs 0.775 kg and is easily carried in one hand the larger container weighs less than 22kg and is easily portable with carrying handles or in a cart... 

Haider and Karlsson [15] developed a simple procedure for the determination of aromatic antioxidants and ultraviolet stabilizers in polyethylene using ultrasonic extraction. Chloroform was used for the isolation of Chi-massorb 944 from 150-pm-thick commerical low-density polyethylene and Irganox 1010 and Irgafos 168 from 25-pm medium-density polyethylene film. The recovery of the additives increased remarkably at higher temperatures and longer extraction times. At 60°C, quantitative recovery was achieved in 15, 45, and 60 minutes for Irgafos 168, Irganox 1010, and Chi-massorb 944, respectively. 

The mechanical properties of PTFE at room temperature are similar to those of medium-density polyethylene, i.e., relatively soft with high elongation, and remaining useful over a wide range of temperatures, from cryogenic (just above absolute zero) to 260°C (500°F) its recommended upper use temperature.28 Stress-strain curves are strongly affected by the temperature however, even at 260°C (500°F) the tensile strength is about 6.5 MPa (942 psi).29... 

FT-IR spectroscopy has been used in the investigation of welding crosslinked polyethylene pipes [23]. Three types of crosslinking systems were used namely, peroxide (PEXa), silane (PEXb) and electron beam (PEXc). Scholten and co-workers [23] observed that only PEXa pipes have a satisfactory electrofusion quality. The strength of electrofusion welds of PEXb and PEXc pipes is not acceptable. The most likely explanation for the differences in weld quality is related to the adhesion theory and more specifically to differences in composition. Figure 5.6 shows the infrared spectra of medium density polyethylene (MDPE), PEXa, PEXb and PEXc. 

R. Ochoa, H.V. Woert, W.H. Lee, R. Subramanian, E. Kugler, and PC. Eklund, Catalytic degradation of medium density polyethylene over silica-alumina supports. Fuel Process. Technol., 49, 119 (1996). 

---