Low melting point

The thennal evaporation source was the earliest used to produce metal clusters in the gas phase [H, 12 and 13], mostly for clusters of the alkalis and other low melting point materials. In this technique, a bulk sample is simply... 

In most covalent compounds, the strong covalent bonds link the atoms together into molecules, but the molecules themselves are held together by much weaker forces, hence the low melting points of molecular crystals and their inability to conduct electricity. These weak intermolecular forces are called van der WaaFs forces in general, they increase with increase in size of the molecule. Only... 

These molecules exist in the solid halides, explaining the low melting points of these halides, and also in the vapour phase at temperatures not too far above the boiling point. At higher temperatures, however, dissociation into trigonal planar monomers, analogous to the boron halides, occurs. 

Pure hydroxylamine is a crystalline solid of low melting point (306 K) but is rarely prepared because it decomposes above 288 K... 

Zincill) chloride. ZnCl2, is the only important halide—it is prepared by standard methods, but cannot be obtained directly by heating the hydrated salt. It has a crystal lattice in which each zinc is surrounded tetrahedrally by four chloride ions, but the low melting point and solubility in organic solvents indicate some covalent... 

Table 14.2 shows that all three elements have remarkably low melting points and boiling points—an indication of the weak metallic bonding, especially notable in mercury. The low heat of atomisation of the latter element compensates to some extent its higher ionisation energies, so that, in practice, all the elements of this group can form cations in aqueous solution or in hydrated salts anhydrous mercuryfll) compounds are generally covalent. 

Distillation of solids under reduced pressure.—The apparatus shown in Fig. II, 19, 1 may be employed for the distillation under diminished pressure of solids possessing comparatively low melting points ... 

The chief disadvantage of the simple vacuum distillation set up shown in Fig. 11,19, 1 is that, if more than one fraction is to be collected, the whole process must be stopped in order to change the receiver B. It is of value, however, for the distillation of solids of low melting point the distillate can easily be removed from the receiver by melting and pouring out. For routine work, involving the collection of several fractious under reduced pressure, the most convenient receiver is the so-called Perkin triangle the complete apparatus for vacuum distillation is depicted in F g. 11,20, 1. The Claisen fla.sk A is fitted to a. short water... 

Another method, which is especiafly suitable for low melting point solids or solids which decompose at low temperatures, is to place the material on a porous plate or pad of drying paper, and to cover the latter with another sheet of Alter paper perforated with a number of holes or with a large clock glass or sheet of glass supported upon corks. The air drying is continued until the solvent has been completely eliminated. 

AUphatic nitriles are usually liquids or low melting point sohds. The most important reaction of a nitrile is its hydrolysis either by an alkaU or by an acid to the corresponding ahphatic acid characterisation of the acid enables the identity of the original nitrile to be established. 

Secondary amines upon treatment with nitrous acid yield nitrosamiues, which are stable, neutral yellow liquids (or low melting point solids), for example ... 

Aromatic nitriles are generally liquids or low melting point solids, and usually have characteristic odours. They give no ammonia with aqueous sodium hydroxide solution in the cold, are hydrolysed by boiling aqueous alkali but more slowly than primary amides ... 

Thermoplastic Fibers. The thermoplastic fibers, eg, polyester and nylon, are considered less flammable than natural fibers. They possess a relatively low melting point furthermore, the melt drips rather than remaining to propagate the flame when the source of ignition is removed. Most common synthetic fibers have low melting points. Reported values for polyester and nylon are 255—290°C and 210—260°C, respectively. 

Ca.ndy. Its low melting point and sugar inversion properties make malic acid a desirable acidulant, especially in hard candy products (44,45). Due to their insolubiUty, hard water salts can cause clouding of the finished product. However, because of the higher solubiUty of calcium malate [17482-42-7] relative to alternative acidulants, clarity of the finished product is enhanced. Additionally, in sugar confectionery products where acidulation may exceed 2.0%, malic acid can provide economic benefits. 

Fused Salt Electrolysis. Only light RE metals (La to Nd) can be produced by molten salt electrolysis because these have a relatively low melting point compared to those of medium and heavy RE metals. Deposition of an alloy with another metal, Zn for example, is an alternative. The feed is a mixture of anhydrous RE chlorides and fluorides. The materials from which the electrolysis cell is constmcted are of great importance because of the high reactivity of the rare-earth metals. Molybdenum, tungsten, tantalum, or alternatively iron with ceramic or graphite linings are used as cmcible materials. Carbon is frequently used as an anode material. 

Lithium Halides. Lithium haHde stabiHty decreases with increasing atomic weight of the halogen atom. Hence, the solubiHty increases from the sparingly soluble Hthium fluoride to the very soluble bromide and iodide salts. The low melting points of Hthium haHdes are advantageous for fluxes in many appHcations. 

---