Lasers neodymium

Neodymium and YAG Lasers. The principle of neodymium and YAG lasers is very similar to that of the ruby laser. Neodymium ions (Nd +) are used in place of Cr + and are often distributed in glass rather than in alumina. The light from the neodymium laser has a wavelength of 1060 nm (1.06 xm) it emits in the infrared region of the electromagnetic spectrum. Yttrium (Y) ions in alumina (A) compose a form of the naturally occurring garnet (G), hence the name, YAG laser. Like the ruby laser, the Nd and YAG lasers operate from three- and four-level excited-state processes. 

Solid-state lasers, such as the ruby laser, neodymium doped yttrium aluminium garnet (Nd-YAG) laser and the titanium doped sapphire laser. 

Neodymium-doped yttrium aluminum garnet laser (NldiYAG)... 

Solid-State Lasers. Sohd-state lasers (37) use glassy or crystalline host materials containing some active species. The term soHd-state as used in connection with lasers does not imply semiconductors rather it appHes to soHd materials containing impurity ions. The impurity ions are typically ions of the transition metals, such as chromium, or ions of the rare-earth series, such as neodymium (see Lanthanides). Most often, the soHd material is in the form of a cylindrical rod with the ends poHshed flat and parallel, but a variety of other forms have been used, including slabs and cylindrical rods with the ends cut at Brewster s angle. 

This is in contrast to lasers based on mby or neodymium in glass, which operate at much lower pulse-repetition rates. Nd YAG lasers are often operated as frequency-doubled devices so that the output is at 532 nm. These lasers are the most common type of soHd-state laser and have dominated sohd-state laser technology since the early 1970s. Nd YAG lasers having continuous output power up to 1800 W are available, but output powers of a few tens of watts are much more common. 

The light source for excitation of Nd YAG lasers may be a pulsed flashlamp for pulsed operation, a continuous-arc lamp for continuous operation, or a semiconductor laser diode, for either pulsed or continuous operation. The use of semiconductor laser diodes as the pump source for sohd-state lasers became common in the early 1990s. A variety of commercial diode-pumped lasers are available. One possible configuration is shown in Figure 8. The output of the diode is adjusted by composition and temperature to be near 810 nm, ie, near the peak of the neodymium absorption. The diode lasers are themselves relatively efficient and the output is absorbed better by the Nd YAG than the light from flashlamps or arc lamps. Thus diode-pumped sohd-state lasers have much higher efficiency than conventionally pumped devices. Correspondingly, there is less heat to remove. Thus diode-pumped sohd-state lasers represent a laser class that is much more compact and efficient than eadier devices. 

The term solid-state laser refers to lasers that use solids as their active medium. However, two kinds of materials are required a host crystal and an impurity dopant. The dopant is selected for its ability to form a population inversion. The Nd YAG laser, for example, uses a small number of neodymium ions as a dopant in the solid YAG (yttrium-aluminum-gar-net) crystal. Solid-state lasers are pumped with an outside source such as a flash lamp, arc lamp, or another laser. This energy is then absorbed by the dopant, raising the atoms to an excited state. Solid-state lasers are sought after because the active medium is relatively easy to handle and store. Also, because the wavelength they produce is within the transmission range of glass, they can be used with fiber optics. 

The volatility of trifluoroacetyl chloride may explain the smooth reaction when preparing neodymium(tris)dichlorophosphate, which is of some interest for dye-lasers, from trifluoroacetate and POCI3 (79) ... 

Neodymium-doped yttrium-aluminum garnet is among the most commonly applied laser material and has broad application (neodymium-YAG). 

Lasers are devices for producing coherent light by way of stimulated emission. (Laser is an acronym for light amplification by stimulated emission of radiation.) In order to impose stimulated emission upon the system, it is necessary to bypass the equilibrium state, characterized by the Boltzmann law (Section 9.6.2), and arrange for more atoms to be in the excited-state E than there are in the ground-state E0. This state of affairs is called a population inversion and it is a necessary precursor to laser action. In addition, it must be possible to overcome the limitation upon the relative rate of spontaneous emission to stimulated emission, given above. Ways in which this can be achieved are described below, using the ruby laser and the neodymium laser as examples. 

Solid-state lasers using substitutional neodymium (Nd3+ ions) as the active defects are widely available. Practical lasers contain about 1% Nd3+ dopant. The most common host materials are glass, yttrium aluminum garnet (YAG), Y3A15012, and calcium tungstate, CaW04. In the crystalline host structures, the defects responsible for amplification are NdY and Ndca-... 

Figure 9.22 Energy levels of most importance in the neodymium laser. The pump transition is from the ground state to the broad 5d 6s band. The main laser transition is between the 4F and 4Ih/2 levels. Internal transitions are marked with dotted lines.

---