Hysteresis definition

Adsorbents such as some silica gels and types of carbons and zeolites have pores of the order of molecular dimensions, that is, from several up to 10-15 A in diameter. Adsorption in such pores is not readily treated as a capillary condensation phenomenon—in fact, there is typically no hysteresis loop. What happens physically is that as multilayer adsorption develops, the pore becomes filled by a meeting of the adsorbed films from opposing walls. Pores showing this type of adsorption behavior have come to be called micropores—a conventional definition is that micropore diameters are of width not exceeding 20 A (larger pores are called mesopores), see Ref. 221a. 

Since by definition r is less than r , the pressure P, for intrusion will be greater than that for extrusion, P , and there will be hysteresis. 

Type I isotherms are characterized by a plateau which is nearly or quite horizontal, and which may cut the p/p° = 1 axis sharply or may show a tail as saturation pressure is approached (Fig. 4.1). The incidence of hysteresis varies many Type I isotherms exhibit no hysteresis at all (Fig. 4.1), others display a definite loop, and in others there is hysteresis which may or may not persist to the lowest pressures ( low-pressure hysteresis ) (Fig. 4.2). Type 1 isotherms are quite common, and are no longer restricted, as seemed at one time to be the case, to charcoals. Many solids, if suitably prepared, will yield Type 1 isotherms the xerogcls of silica, titania, alumina... 

Static performance measurements related to positioner/ac tuator operation are conformity, measured accuracy, hysteresis, dead baud, repeatability, and locked stem-pressure gain. Definitions and standardized test procedures for determining these measurements can be found in ISA-S75.13-1989, Method of Evaluating the Performance of Positioners with Analog Input Signals and Pneumatic Output . 

For the special case of [(LCu)2Dy][Mo(CN)8]-CH3CN-H20 H, where L2-is A/, A/, -propylenebis(3-methoxysalicylideneiminato) anion, slow relaxation is observed (A = 19.IK, r0 = 1.28 X 10 7s) [109] and for [(LCu)2Tb] [Fe(CN)8]-4H20 , where L2 is the Ar,AT -propylene-bis(3-methoxysalicylideneiminato) anion (Figure 4.12), hysteresis has been observed in the millikelvin region using the microSQUID technique [108]. However, there is no definitive evidence that magnetic slow relaxation arises from SCM behaviour and not from SMM tectons. 

N2 adsorption-desorption isotherms and pore size distribution of sample II-IV are shown in Fig. 4. Its isotherm in Fig. 4a corresponds to a reversible type IV isotherm which is typical for mesoporous solids. Two definite steps occur at p/po = 0.18, and 0.3, which indicates the filling of the bimodal mesopores. Using the BJH procedure with the desorption isotherm, the pore diameter in Fig. 4a is approximately 1.74, and 2.5 nm. Furthermore, with the increasing of synthesis time, the isotherm in Fig. 4c presents the silicalite-1 material related to a reversible type I isotherm and mesoporous solids related to type IV isotherm, simultaneously. These isotherms reveals the gradual transition from type IV to type I. In addition, with the increase of microwave irradiation time, Fig. 4c shows a hysteresis loop indicating a partial disintegration of the mesopore structure. These results seem to show a gradual transformation... 

The term piezoelectric nonlinearity is used here to describe relationship between mechanical and electrical fields (charge density D vs. stress a, strain x vs. electric field E) in which the proportionality constant d, is dependent on the driving field, Figure 13.1. Thus, for the direct piezoelectric effect one may write D = d(a)a and for the converse effect x = d(E)E. Similar relationships may be defined for other piezoelectric coefficients (g, h, and e) and combination of electro-mechanical variables. The piezoelectric nonlinearity is usually accompanied by the electro-mechanical (D vs. a or x vs. E) hysteresis, as shown in Figure 13.2. By hysteresis we shall simply mean, in the first approximation, that there is a phase lag between the driving field and the response. This phase lag may be accompanied by complex nonlinear processes leading to a more general definition of the hysteresis [2],... 

Measurement of contact angles hysteresis. The experimental determination of contact angles is complicated by two factors first, that the angle depends on the surface tension of the liquid surface second, that the angle is rarely definite, but may have any value between two extremes, according as the liquid is tending to advance over a dry surface, or to recede from a previously wetted one. 

---