Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Glow plugs

Glow plug Fuel heater Swirl chamber Piston ring Turbo rotor... [Pg.308]

Using a torch and plumbers solder, solder the glow plug into the end of the pipe. [Pg.61]

Solder two wires to the tip and body of the glow plug. Do not allow the wires to touch. [Pg.61]

Check the glow plug by touching the wires to a 1 1/2 volt battery. By looking down the bore of the... [Pg.61]

Solder the switch to the glow plug wires. Make sure mat they do not touch each other. [Pg.62]

Pour a small quantity of flash-powder into the bore to cover the glow plug. Tap the barrel lightly to make sure that the powder flows into contact with the filament. This is the primer charge. Pour about one grain of pistol powder to cover the primer charge. Tamp in place with a small wad of cotton. [Pg.134]

Pour epoxy resin into the projector until the glow plug is covered with a layer about 1/2" deep. Make sure the resin flows to completely fill the space around the barrel. Let harden. [Pg.134]

Thread the glow-plug into the pipe cap and screw the cap onto the large pipe nipple. [Pg.140]

Pour the flash-powder into the glow-plug and seal it in place with a piece of cellophane tape. [Pg.140]

Glow Plug A device used to provide heat to the prechamber of an indirect injected diesel engine. It is used in cold conditions to permit ease of starting. The glow plugs have a preheating time of about seven seconds. [Pg.348]

Automotive Valve plate in common rail systems Glow plugs for diesel engines and additional car heating Fuel injector parts, valves, valve train components, rocker arm pads, tappet disks, cam follower roller, turbocharger rotors tappet shim precombustion chambers... [Pg.144]

Borba, M.L.O. and Abreu, R.S. B-39 Use of Glow-Plugs in order to Obtain Multifuel Capability of Diesel Engines , Instituto Maua de Tecnologia, IV International Symposium on Alcohol Fuels Technology, Guaruja, 1980. [Pg.52]

Alloy 602 CA a modification of other 600 alloys is used in heat-treating, annealing furnaces, furnace rolls, high-temperature calcination application, catalytic support systems, and glow plugs in automobiles, vitrification of nuclear waste 800, 45 TM Have high creep and rupture strength and oxidation resistance used... [Pg.247]

See other pages where Glow plugs is mentioned: [Pg.323]    [Pg.420]    [Pg.429]    [Pg.431]    [Pg.432]    [Pg.432]    [Pg.432]    [Pg.433]    [Pg.191]    [Pg.380]    [Pg.332]    [Pg.61]    [Pg.69]    [Pg.69]    [Pg.133]    [Pg.134]    [Pg.139]    [Pg.140]    [Pg.349]    [Pg.124]    [Pg.132]    [Pg.191]    [Pg.232]    [Pg.232]    [Pg.232]    [Pg.323]    [Pg.420]    [Pg.429]    [Pg.430]    [Pg.431]    [Pg.432]    [Pg.432]    [Pg.432]    [Pg.433]    [Pg.380]    [Pg.140]    [Pg.140]   
See also in sourсe #XX -- [ Pg.140 ]

See also in sourсe #XX -- [ Pg.230 , Pg.347 ]



SEARCH



Glow

© 2024 chempedia.info