Fiber thermal property

LDPE/EPDM and HOPE/ EPDM modified with LDPE-g-MAH reinforced with jute fibers Thermal properties Influence of compatibilizer on the thermal and mechanical properties of the bltaids was studied Sarkhel and Choudhury 2008... 

The industrial value of furfuryl alcohol is a consequence of its low viscosity, high reactivity, and the outstanding chemical, mechanical, and thermal properties of its polymers, corrosion resistance, nonburning, low smoke emission, and exceUent char formation. The reactivity profile of furfuryl alcohol and resins is such that final curing can take place at ambient temperature with strong acids or at elevated temperature with latent acids. Major markets for furfuryl alcohol resins include the production of cores and molds for casting metals, corrosion-resistant fiber-reinforced plastics (FRPs), binders for refractories and corrosion-resistant cements and mortars. 

Table 2. Thermal Properties of Olefins and Other Fiber-Forming Polymers...

Density, mechanical, and thermal properties are significantly affected by the degree of crystallinity. These properties can be used to experimentally estimate the percent crystallinity, although no measure is completely adequate (48). The crystalline density of PET can be calculated theoretically from the crystalline stmcture to be 1.455 g/cm. The density of amorphous PET is estimated to be 1.33 g/cm as determined experimentally using rapidly quenched polymer. Assuming the fiber is composed of only perfect crystals or amorphous material, the percent crystallinity can be estimated and correlated to other properties. 

Thermal Properties. Fibers are not thermoplastic and stable to temperatures below 150°C, with the possible exception of slight yellowing. They begin to lose strength gradually above 170°C, and decompose more rapidly above 300°C. They ignite at 420°C and have a heat of combustion of 14,732 J/g (3.5 kcal/g). 

Oxide fibers are manufactured by thermal or chemical processes into a loose wool mat, which can then be fabricated into a flexible blanket combined with binders and formed into boards, felts, and rigid shapes or fabricated into ropes, textiles and papers. The excellent thermal properties of these products make them invaluable for high temperature industrial appHcations. 

Thermal Properties. Spider dragline silk was thermally stable to about 230°C based on thermal gravimetric analysis (tga) (33). Two thermal transitions were observed by dynamic mechanical analysis (dma), one at —75° C, presumed to represent localized mobiUty in the noncrystalline regions of the silk fiber, and the other at 210°C, indicative of a partial melt or a glass transition. Data from thermal studies on B. mori silkworm cocoon silk indicate a glass-transition temperature, T, of 175°C and stability to around 250°C (37). The T for wild silkworm cocoon silks were slightly higher, from 160 to 210°C. 

Composites fabricated with the smaller floating catalyst fiber are most likely to be used for applications where near-isotropic orientation is favored. Such isotropic properties would be acceptable in carbon/carbon composites for pistons, brake pads, and heat sink applications, and the low cost of fiber synthesis could permit these price-sensitive apphcations to be developed economically. A random orientation of fibers will give a balance of thermal properties in all axes, which can be important in brake and electronic heat sink applications. 

Key Words —Nanotubes, mechanical properties, thermal properties, fiber-reinforced composites, stiffness constant, natural resonance. 

Fig. 6-14 specific modulus = modulus/density. Plastics include use of the heat-resistant TPs such as the polimides, polyamide-imide, and others. Table 6-21 provides data on the thermal properties of RPs. To date at least 80 wt % are glass fiber and about 60 wt% of those are polyester (TS) type RPs. 

PET, PTT, and PBT have similar molecular structure and general properties and find similar applications as engineering thermoplastic polymers in fibers, films, and solid-state molding resins. PEN is significantly superior in terms of thermal and mechanical resistance and barrier properties. The thermal properties of aromatic-aliphatic polyesters are summarized in Table 2.6 and are discussed above (Section 2.2.1.1). 

Poly(/)-phenylenctcrcphthalamiclc) forms a liquid crystalline solution and can be spun into a fiber with a very high orientation these fibers have excellent tensile and thermal properties. These high-modulus fibers are suitable as reinforcing materials in technical applications. 

Polymerization reactions. Polymerization of ethylene to polyethylene has been conducted at pilot-plant scales reaching a target of 1500 tons per year. Some reactions, including polymerization and copolymerization of polymers for grafting on textile fibers, have been successfully performed. Similarly, cross-linking of polyethylene to improve thermal properties has also been achieved. 

Thermal properties. See also Temperature of aromatic polyamides, 19 718 of asbestos, 3 300-304 of diesel fuel, 12 423 of ethylene—tetrafluoroethylene copolymers, 18 319-321 of fibers, 11 167 of filled polymers, 11 309—310 of gallium, 12 342 of glass, 12 588... 

Many researchers have reported the structure-thermal property correlations in LCPs from substituted hydroquinones (HQs) and dicarboxylic acids. Lenz and co-workers have investigated the liquid crystallinity of the polyarylates obtained from substituted HQs and terephthalic acid (TA) [6-10], substituted HQs and l,10-bis(phenoxy)decane-4,4/-dicarboxylic acid [8], and substituted HQs and a,oo-bis(phenoxy)alkane-4,4/-dicarboxylic acid [11], Kricherdorf and Schwarz [12] and Osman [13] reported the liquid crystallinity of the polyarylates obtained from substituted HQs and 1,4-cyclohexanedicarboxylic acid, while Krigbaum el al. [14], Heitz and co-workers [15] and Kricherdorf and Engelhardt [16] investigated the liquid crystallinity of the polyarylates synthesized from substituted HQs and substituted TAs. In addition, Jackson reported the liquid crystallinity and the moduli of fibers and injection molded specimens of the polyarylates... 

The reason for the lower liquid crystalline (LC) temperature of the BB model compound seems to be that the biphenyl unit of this compound was adopting a twisted structure in the LC state [26], Therefore, we prepared various polyarylates containing the BB unit and determined their thermal properties and the moduli of the as-spun fibers, as shown in Table 19.3. 

Table 19.4 Thermal properties and moduli of as-spun fibers and injection molded specimens of Ph-HQ/BB and Ph-HQ/HQ/BB (m/n = 50/50) polyarylates [19] From Inoue, T. and Tabata., N., Mol. Cryst. Liq. Cryst, 254, 417-428 (1994), and reproduced with permission of Gordon and Breach (Taylor and Francis) Publishers...

---