Dipolar interactions dipole moments

Consider the interaction of a neutral, dipolar molecule A with a neutral, S-state atom B. There are no electrostatic interactions because all the miiltipole moments of the atom are zero. However, the electric field of A distorts the charge distribution of B and induces miiltipole moments in B. The leading induction tenn is the interaction between the pennanent dipole moment of A and the dipole moment induced in B. The latter can be expressed in tenns of the polarizability of B, see equation (Al.S.g). and the dipole-mduced-dipole interaction is given by... 

The frequency dependence is taken into accoimt through a mixed time-dependent method which introduces a dipole-moment factor (i.e. a polynomial of first degree in the electronic coordinates ) in a SCF-CI (Self Consistent Field with Configuration Interaction) method (3). The dipolar factor, ensuring the gauge invariance, partly simulates the molecular basis set effects and the influence of the continuum states. A part of these effects is explicitly taken into account in an extrapolation procedure which permits to circumvent the sequels of the truncation of the infinite sum-over- states. 

Here we focus on the effect of dipolar dispersion laws for high-frequency collective vibrations on the shift and width of their spectral line, with surface molecules inclined at an arbitrary angle 6 to the surface-normal direction. For definiteness, we consider the case of a triangular lattice and the ferroelectric ordering of dipole moments inherent in this lattice type.56,109 Lateral interactions of dynamic dipole moments p = pe (e = (sin os, sin6fcin , cos )) corresponding to collective vibrations on a simple two-dimensional lattice of adsorbed molecules cause these vibrations to collectivize in accordance with the dispersion law 121... 

To answer this question, let us first consider a neutral molecule that is usually said to be polar if it possesses a dipole moment (the term dipolar would be more appropriate)1 . In solution, the solute-solvent interactions result not only from the permanent dipole moments of solute or solvent molecules, but also from their polarizabilities. Let us recall that the polarizability a of a spherical molecule is defined by means of the dipole m = E induced by an external electric field E in its own direction. Figure 7.1 shows the four major dielectric interactions (dipole-dipole, solute dipole-solvent polarizability, solute polarizability-solvent dipole, polarizability-polarizability). Analytical expressions of the corresponding energy terms can be derived within the simple model of spherical-centered dipoles in isotropically polarizable spheres (Suppan, 1990). These four non-specific dielectric in-... 

It was found that a better representation of non-specific interactions between solvents and the monosubstituted dipolar trimethylammonium ions is gained from the product of tt and the solvent dipole moment (/x). The obtained results were compared with the gas-phase basicity and the solvent attenuation factors (SAF) were calculated". 

According to the electrostatic model the solvation is due to electrostatic interaction between the charged ions and the dipolar solvent molecules. Thus the solvating and ionizing properties of a solvent are considered as being due primarily to the dipole moment of the solvent molecules. Thus, ionic compounds such as sodium chloride are insoluble in non-polar solvents such as carbon tetrachloride. Actually, rather than the dipole moment the field action of the dipoles should be considered. This approach might explain why acetonitrile (p = 3.2) is poor in its ionizing properties compared to water (p = 1.84). However, no numerical values are available for this quantity. 

Carbon dioxide is a symmetric linear molecule with zero dipole moment. Hence its interaction with a dipolar molecule like H20 is weak. However, it is moderately soluble in water and in many other organic solvents. The solubility equilibrium can be described by Eq. (1) ... 

Response of the mean square dipole moment, < J2>, to excluded volume is evaluated for several chains via Monte-Carlo methods. The chains differ in the manner in which dipolar moment vectors are attached to the local coordinate systems for the skeletal bonds. In the unperturbed state, configurational statistics are those specified by the usual RIS model for linear PE chains. Excluded volume is introduced by requiring chain atoms participating in long-range interactions to behave as hard spheres. 

---