Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Cures degree

Recently, a novel hydrophylic polymer membrane based on poly(allylamine hydrochloride) (PAA.HC1)/PVA, crosslinked with GA, has been also tested for methanol dehydration by pervaporation technique [33], Even if the reported results show a small selectivity of the last type of membrane, the blend s composition, the curing degree and the process conditions (temperature, feed concentration, etc.) could be used to obtain a better separation of methanol. [Pg.134]

No regulatory reporting or Energy needed to cure 1 g Control of cure degree of... [Pg.257]

Even below the temperature at which thermal breakdown becomes significant, there may be large variations in friction and wear with temperature. The nature and extent of the variations are generally inconsistent and unpredictable, depending on the type of binder, concentration of lubricant, other components present in the coating, completeness of film curing, degree of consolidation and the test method used. [Pg.202]

Diene content Cure degree and fast rate Scorch resistance... [Pg.119]

Figure 6.13 Contact-resistance changes for three different cure degrees versus time at 30 k ... Figure 6.13 Contact-resistance changes for three different cure degrees versus time at 30 k ...
D2196 and [MIL-STD-883, resistance IPC- cure degree of (ASTM D2240) (no standard method)... [Pg.347]

N.S. Koupis, L.C. Martens, R.M.H. Verbeeck, Relative curing degree of polyacid-modified and conventional resin composites determined by surface Knoop hardness. Dent. Mater. 22 (2006) 1045-1050. [Pg.82]

For mechanically mixed resin and rubber, the SKD-ICTRA rubber concentration has essentially no effect upon the value of ic- For thermally treated mechanical mixtures, the value of Kic increases about twofold. If the thermal treatment of the specimens was performed after the compoimd was completely cured (degree of conversion not less than 93%), the heating does not effect the level of phase separation but it alters the interphase interaction between the components not only by increasing the strength of the resin itself but also through the abrupt increase of the effect of the rubber upon Kiq. [Pg.148]

When revitrification occurs at a curing degree a > 0.5, the reaction rate decreases markedly because the glass transition temperature approaches the cure temperature. The reaction becomes diffusion controlled rather than... [Pg.54]

Under-cure degree of cure that is less than optimum. May be evidenced by tackiness, loginess or inferior physical properties. [Pg.143]

Certainly, the cure is related to mechanical strength. The cure is the process during which the modulus of the resin becomes large. In the last stage of cure, in which the sensitivity of some analysis techniques decreases rapidly, cure degree can be reflected in the mechanical strength in an obvious way. Therefore, the cure process can be studied successfully with mechanical methods 149,50]. Torsional... [Pg.406]

There is no doubt that proper curing is very important for joint reliability. It was found that a minimum curing degree is required to provide a certain level of mechanical and electrical performance of adhesive joints, especially with nonnoble metallizations (Ref 14). Once this is achieved, increasing curing times does not result in significant improvement. [Pg.251]

Comparison of curing degree with time between ACF and NCF... [Pg.1304]

Abstract The effects of three degrees of cure (low, standard and postcured) on two carbon reinforced epoxy resins are examined. The polymerization degree is tentatively assessed by thermal antdysis techniques, namely by Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The effects on both static mechanical and fracture toughness properties have been checked. It has been found that the glass transition temperature measured by DMA is the parameter, among those studied (both thermal and mechanical), that is more sensitive to the cure degrees. [Pg.206]

Keywords epoxy resin, cure degree, thermal analysis... [Pg.206]

In Table 6 the cure assessment results by means of differoit thermal analysis techniques ate qualitatively summarized as it can be seen, the situations obtained afier the different cure cycles are not as clear as one wishes even in a qualitative way. In fact an uncertainty on Material A cure degree could arise because the different ways (by DMA-tan 8, by DMA-Log E , by DSC-Tg or by DSC-AHr s) of evaluating die polymerization degree seem to show a different trend Probably in that case the... [Pg.213]

From a QUANTITATIVE point of view it seems that DMA is more reliable than DSC to establish the cure degree of a composite because the Tg shift is more easy-to-quantify than the residual heat. [Pg.214]

Crack growth, 109 slow, 146 Cracking, stress D 1693,146 Creep compliance, 10 Cure degree, 206... [Pg.221]


See other pages where Cures degree is mentioned: [Pg.363]    [Pg.99]    [Pg.315]    [Pg.183]    [Pg.212]    [Pg.49]    [Pg.386]    [Pg.81]    [Pg.397]    [Pg.234]    [Pg.141]    [Pg.251]    [Pg.251]    [Pg.252]    [Pg.252]    [Pg.259]    [Pg.49]    [Pg.205]    [Pg.206]    [Pg.214]    [Pg.218]   
See also in sourсe #XX -- [ Pg.183 ]




SEARCH



Degree of cure

Degree of cure measurements

Laminates Cure, degree

© 2024 chempedia.info