Cuprate reagents reactions

The most frequently used organocuprates are those m which the alkyl group is pri mary Steric hindrance makes secondary and tertiary dialkylcuprates less reactive and they tend to decompose before they react with the alkyl halide The reaction of cuprate reagents with alkyl halides follows the usual 8 2 order CH3 > primary > secondary > tertiary and I > Br > Cl > F p Toluenesulfonates are somewhat more reactive than halides Because the alkyl halide and dialkylcuprate reagent should both be primary m order to produce satisfactory yields of coupled products the reaction is limited to the formation of RCH2—CH2R and RCH2—CH3 bonds m alkanes... 

Since this original synthesis, a great number of improvements (191—201) have been made in the stereoselective preparation and derivatization of the CO-chain precursor, in cuprate reagent composition and preparation, in protecting group utilization, and in the preparation and resolution of hydroxycyclopentenones. Illustration of some of the many improvements are seen in a synthesis (202) of enisoprost, a PGE analogue. The improvements consist of a much more efficient route to the enone as well as modifications in the cuprate reactions. Preparation of the racemic enone is as follows ... 

The formation of g-alkyl-a,g-unsaturated esters by reaction of lithium dialkylcuprates or Grignard reagents in the presence of copper(I) iodide, with g-phenylthio-, > g-acetoxy-g-chloro-, and g-phosphoryloxy-a,g-unsaturated esters has been reported. The principal advantage of the enol phosphate method is the ease and efficiency with which these compounds may be prepared from g-keto esters. A wide variety of cyclic and acyclic g-alkyl-a,g-unsaturated esters has been synthesized from the corresponding g-keto esters. However, the method is limited to primary dialkylcuprates. Acyclic g-keto esters afford (Zl-enol phosphates which undergo stereoselective substitution with lithium dialkylcuprates with predominant retention of stereochemistry (usually > 85-98i )). It is essential that the cuprate coupling reaction of the acyclic enol phosphates be carried out at lower temperatures (-47 to -9a°C) to achieve high stereoselectivity. When combined with they-... 

In addition to the boron trifluoride-diethyl ether complex, chlorotrimcthylsilanc also shows a rate accelerating effect on cuprate addition reactions this effect emerges only if tetrahydrofuran is used as the reaction solvent. No significant difference in rate and diastereoselectivity is observed in diethyl ether as reaction solvent when addition of the cuprate, prepared from butyllithium and copper(I) bromide-dimethylsulfide complex, is performed in the presence or absence of chlorotrimethylsilane17. If, however, the reaction is performed in tetrahydrofuran, the reaction rate is accelerated in the presence of chlorotrimethylsilane and the diastereofacial selectivity increases to a ratio of 88 12 17. In contrast to the reaction in diethyl ether, the O-silylated product is predominantly formed in tetrahydrofuran. The alcohol product is only formed to a low extent and showed a diastereomeric ratio of 55 45, which is similar to the result obtained in the absence of chlorotrimethylsilane. This discrepancy indicates that the selective pathway leading to the O-silylated product is totally different and several times faster than the unselective pathway" which leads to the unsilylated alcohol adduct. A slight further increase in the Cram selectivity was achieved when 18-crown-6 was used in order to increase the steric bulk of the reagent. 

Excellent selectivities are also observed with (CH,)2CuZnCl, Bti2CiiTi[OCH(CH3)2], and BnCu BF3. The reaction of a standard cuprate reagent, e.g., lithium dibutylcuprate, with ( )-l in tetrahydrofuran gives predominantly the SN2 product. 

The procedure described here illustrates the preparation of mixed lithium arylhetero(alkyl)cuprate reagents and their reactions with carboxylic acid chlorides,4 These mixed cuprate reagents also react with a,a -dibromoketones,12 primary alkyl halides,4 and a,/3-unsaturated ketones,4 with selective transfer of only the alkyl group. 

Scheme 4.10 gives some examples of application of alkyne carboalumination in synthesis. The reaction in Entry 1 was carried out as part of a synthesis of the immunosuppressant drug FK-506. The vinyl alane was subsequently transmetallated to a cuprate reagent (see Chapter 8). In Entry 2, the vinyl alane was used as a nucleophile for opening an epoxide ring and extending the carbon chain by two atoms. In Entries 3 to 5, the vinyl alane adducts were converted to vinyl iodides. In Entry 6, the vinyl alane was converted to an ate reagent prior to reaction with formaldehyde. 

Conjugate addition reactions involving organocopper intermediates can be made enantioselective by using chiral ligands.86 Several mixed cuprate reagents containing... 

Give the products expected from each of the following reactions involving mixed cuprate reagents. 

Organoboranes can also be made using organocopper reagents. One route to methyl and aryl derivatives is by reaction of a dialkylborane, such as 9-BBN, with a cuprate reagent.4... 

---