Cross-linking glass transition

Polymers will be elastic at temperatures that are above the glass-transition temperature and below the liquiflcation temperature. Elasticity is generally improved by the light cross linking of chains. This increases the liquiflcation temperature. It also keeps the material from being permanently deformed when stretched, which is due to chains sliding past one another. Computational techniques can be used to predict the glass-transition and liquiflcation temperatures as described below. 

Irregularities such as branch points, comonomer units, and cross-links lead to amorphous polymers. They do not have true melting points but instead have glass transition temperatures at which the rigid and glasslike material becomes a viscous liquid as the temperature is raised. 

Elastomeric Modified Adhesives. The major characteristic of the resins discussed above is that after cure, or after polymerization, they are extremely brittie. Thus, the utility of unmodified common resins as stmctural adhesives would be very limited. Eor highly cross-linked resin systems to be usehil stmctural adhesives, they have to be modified to ensure fracture resistance. Modification can be effected by the addition of an elastomer which is soluble within the cross-linked resin. Modification of a cross-linked resin in this fashion generally decreases the glass-transition temperature but increases the resin dexibiUty, and thus increases the fracture resistance of the cured adhesive. Recendy, stmctural adhesives have been modified by elastomers which are soluble within the uncured stmctural adhesive, but then phase separate during the cure to form a two-phase system. The matrix properties are mosdy retained the glass-transition temperature is only moderately affected by the presence of the elastomer, yet the fracture resistance is substantially improved. 

Substituted nonheat-reactive resins do not form a film and are not reactive by themselves, but are exceUent modifier resins for oleoresinous varnishes and alkyds. Thein high glass-transition temperature and molecular weight provide initial hardness and reduce tack oxygen-initiated cross-linking reactions take place with the unsaturated oils. 

Fig. 19. Generalized modulus—temperature curves for polymeric materials showing the high modulus glassy state, glass-transition regions for cured and uncured polymers, plateau regions for cross-linked polymers, and the dropoff in modulus for a linear polymer.

Glass-Transition Temperature. The T of PVP is sensitive to residual moisture (75) and unreacted monomer. It is even sensitive to how the polymer was prepared, suggesting that MWD, branching, and cross-linking may play a part (76). Polymers presumably with the same molecular weight prepared by bulk polymerization exhibit lower T s compared to samples prepared by aqueous solution polymerization, lending credence to an example, in this case, of branching caused by chain-transfer to monomer. 

A somewhat similar thing happens in many polymers at the glass-rubber transition that we mentioned in Chapter 6. Below the transition these polymers are much more brittle than above it, as you can easily demonstrate by cooling a piece of rubber or polyethylene in liquid nitrogen. (Many other polymers, like epoxy resins, have low Gc values at all temperatures simply because they are heavily cross-linked at all temperatures by covalent bonds and the material does not flow at the crack tip to cause blunting.)... 

As the temperature is decreased, free-volume is lost. If the molecular shape or cross-linking prevent crystallisation, then the liquid structure is retained, and free-volume is not all lost immediately (Fig. 22.8c). As with the melt, flow can still occur, though naturally it is more difficult, so the viscosity increases. As the polymer is cooled further, more free volume is lost. There comes a point at which the volume, though sufficient to contain the molecules, is too small to allow them to move and rearrange. All the free volume is gone, and the curve of specific volume flattens out (Fig. 22.8c). This is the glass transition temperature, T . Below this temperature the polymer is a glass. 

When the temperamre is lowered, rubbers become stiff and brittle. All rubbers eventually stiffen to a rigid, amorphous glass at the glass transition temperature (Tg). This temperature also indicates the low-temperature service limit of the rubber. Tg values are dependent on the structure, degree of cross-linking (vulcanization) and isomeric composition of the rubber. 

Polyisobutylene has a similar chemical backbone to butyl rubber, but does not contain double carbon-carbon bonds (only terminal unsaturation). Many of its characteristics are similar to butyl rubber (ageing and chemical resistance, low water absorption, low permeability). The polymers of the isobutylene family have very little tendency to crystallize. Their strength is reached by cross-linking instead of crystallization. The amorphous structure of these polymers is responsible for their flexibility, permanent tack and resistance to shock. Because the glass transition temperature is low (about —60°C), flexibility is maintained even at temperatures well below ambient temperature. 

---