Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Carbon dioxide molecular weight

Saraf MK (2001) Polymerization of vinylidene fluoride in supercritical carbon dioxide Molecular weight distribution. Masters Thesis, North Carolina State University, Raleigh, NC... [Pg.346]

Ordinary carbon contains about one per cent of C13 and the difference in weight of C12 and C13 is one unit. The atomic weight of ordinary carbon is about 12.01. If the ratio of C13 increases from 1 per cent to 1.1 per cent the atomic weight increases from 12.010 to 12.011, an increase of one part in 12,000. With carbon dioxide, which is the most convenient and most easily purified compound of carbon the molecular weight increases from 44.010 to 44.011, an increase of a little over twenty parts per million. An accuracy of... [Pg.253]

Experiments are described for determining GO2 in carbonated beverages, NaHG03 in Alka-Seltzer tablets, and the molecular weight of GO2. Garbon dioxide is collected in NaOH and the concentrations of G03 are determined by titrating with a standard solution of HGl to the phenolphthalein and methyl orange end points. [Pg.358]

If the initiation reaction is much faster than the propagation reaction, then all chains start to grow at the same time. Because there is no inherent termination step, the statistical distribution of chain lengths is very narrow. The average molecular weight is calculated from the mole ratio of monomer-to-initiator sites. Chain termination is usually accompHshed by adding proton donors, eg, water or alcohols, or electrophiles such as carbon dioxide. [Pg.517]

Reasonable prediction can be made of the permeabiUties of low molecular weight gases such as oxygen, nitrogen, and carbon dioxide in many polymers. The diffusion coefficients are not compHcated by the shape of the permeant, and the solubiUty coefficients of each of these molecules do not vary much from polymer to polymer. Hence, all that is required is some correlation of the permeant size and the size of holes in the polymer matrix. Reasonable predictions of the permeabiUties of larger molecules such as flavors, aromas, and solvents are not easily made. The diffusion coefficients are complicated by the shape of the permeant, and the solubiUty coefficients for a specific permeant can vary widely from polymer to polymer. [Pg.498]

Molecular Weight EPA Method 3 is used to determine carbon dioxide and oxygen concentrations and dry molecular weight of the stack-gas stream. Depending on the intended use of the data, these values can be obtained with an integrated sample (see Fig. 25-28) or a grab sample (see Fig. 25-29). In addition, the instrumental analyzer... [Pg.2198]

With the grab sampling technique, a samphng probe is placed at the center of the stack, and a sample is drawn direcfly into an Orsat analyzer or a Fyrite-type combustion-gas analyzer. The sample is then analyzed for carbon dioxide and oxygen content. With these data, the diy molecular weight of the gas stream can then be calculated. [Pg.2198]

Calculate the heat generated by dissociation and formation as one molecular weight of methane, CHi, burns to carbon dioxide and water. How does this heating value compare to the tabular heating value for methane ... [Pg.96]


See other pages where Carbon dioxide molecular weight is mentioned: [Pg.580]    [Pg.423]    [Pg.580]    [Pg.259]    [Pg.580]    [Pg.423]    [Pg.580]    [Pg.259]    [Pg.35]    [Pg.17]    [Pg.22]    [Pg.171]    [Pg.360]    [Pg.13]    [Pg.225]    [Pg.299]    [Pg.333]    [Pg.459]    [Pg.426]    [Pg.161]    [Pg.184]    [Pg.141]    [Pg.249]    [Pg.270]    [Pg.443]    [Pg.126]    [Pg.52]    [Pg.222]    [Pg.224]    [Pg.227]    [Pg.229]    [Pg.482]    [Pg.331]    [Pg.498]    [Pg.4]    [Pg.107]    [Pg.111]    [Pg.386]    [Pg.513]    [Pg.156]    [Pg.2002]    [Pg.2254]    [Pg.2254]    [Pg.37]    [Pg.417]    [Pg.794]   
See also in sourсe #XX -- [ Pg.22 ]

See also in sourсe #XX -- [ Pg.3 ]




SEARCH



Carbon weight

© 2024 chempedia.info