Anisotropic carbon

Other Uses. Anisotropic and isotropic carbon are produced from furfural-modified systems glassy carbon is produced primarily from furfuryl alcohol or BHMF resins (78,79). 

Manganese—Aluminum—Carbon Alloys. Anisotropic Mn—Al—C permanent magnet ahoys have been developed usiag warm working (87). Properties as high as B = 0.61 T (6100 G), = 220 kA/m (2.8 kOe) and (BH) = 56 kJ/m (7 x 10 G-Oe) have been obtained. A typical ahoy... 

Mesophase formation in coal-tar pitch is encouraged by a reduction of the natural quinoline-insoluble matter content, which resembles carbon black but is not optically anisotropic and is characterized by an atomic carbon hydrogen ratio of 4 1. In contrast, the atomic carbon hydrogen ratio of mesophase is about 2 1. 

Fibers produced from pitch precursors can be manufactured by heat treating isotropic pitch at 400 to 450°C in an inert environment to transform it into a hquid crystalline state. The pitch is then spun into fibers and allowed to thermoset at 300°C for short periods of time. The fibers are subsequendy carbonized and graphitized at temperatures similar to those used in the manufacture of PAN-based fibers. The isotropic pitch precursor has not proved attractive to industry. However, a process based on anisotropic mesophase pitch (30), in which commercial pitch is spun and polymerized to form the mesophase, which is then melt spun, stabilized in air at about 300°C, carbonized at 1300°C, and graphitized at 3000°C, produces ultrahigh modulus (UHM) carbon fibers. In this process tension is not requited in the stabilization and graphitization stages. 

An E-Z discrimination between isomeric oxaziridines (27) was made by NMR data (69JCS(C)2650). The methyl groups of the isopropyl side chains in the compounds (27) are nonequivalent due to the neighboring carbon and nitrogen centres of asymmetry and possibly due to restricted rotation around the exocyclic C—N bond in the case of the Z isomer. The chemical shift of a methyl group in (Z)-(27) appears at extraordinarily high field, an effect probably due to the anisotropic effect of the p-nitrophenyl group in the isomer believed to be Z. 

If the amount of the sample is sufficient, then the carbon skeleton is best traced out from the two-dimensional INADEQUATE experiment. If the absolute configuration of particular C atoms is needed, the empirical applications of diastereotopism and chiral shift reagents are useful (Section 2.4). Anisotropic and ring current effects supply information about conformation and aromaticity (Section 2.5), and pH effects can indicate the site of protonation (problem 24). Temperature-dependent NMR spectra and C spin-lattice relaxation times (Section 2.6) provide insight into molecular dynamics (problems 13 and 14). 

C. R. Kenedy, Fracture Toughness of Anisotropic Graphites, Extended Abstracts and Program - 17 Biennial Conference on Carbon, Pub American Carbon Society, 1985, pp 289 290... 

Several structural characterisations of carbon nanotubes (CNTs) with the cylindrical graphite are reviewed from the viewpoint of transmission electron microscopy (TEM). Especially, electron energy loss spectroscopy (EELS) by using an energy-fdtered TEM is applied to reveal the dependence of fine structure of EELS on the diameter and the anisotropic features of CNTs. 

The rare gas atoms are strictly spherical but other systems which have been considered, such as hydrogen, carbon, or halogen atoms, may be anisotropic. These have been treated in preceding sections as isotropic and it is one purpose of the present section to consider the magnitude of possible error. 

In the more complex case of the saturated hydrocarbons, the anisotropic equations have not been solved. Rough estimates from approximate solutions indicated that the anisotropy of hydrogen and of saturated carbon atoms is small but an accurate check on this matter would be desirable. 

Isotropic carbon is obtained by the pyrolysis of a hydrocarbon, usually methane, at high temperature (1200-1500°C) in a fluidized bed on a graphite substrate.Under these conditions, a turbostratic structure is obtained which is characterized by very little ordering and an essentially random orientation of small crystallites. In contrast to graphite which is highly anisotropic, such a structure has isotropic properties (see Ch. 7). Isotropic carbon is completely inert biologically. Its properties are compared to alumina, another common implant material, in Table 17.8. Notable is its high strain to failure. 

---