Butyne-2, hydrogenation

For 1,3-butadiene hydrogenation, the toxicity of sulfur is 3 (Fig. 13). which is lower than the toxicity for olefin hydrogenation. The hydrogenation of 1-butyne has also been studied for various ratios of sulfur over palladium. As was already published (86), the 1-butyne hydrogenation rate increases with time. The same effect has been observed on sulfided palladium. The turnover number is consequently presented for 1-butyne hydrogenation versus the sulfur content for various 1-butyne conversions (see Fig. 14). During the first minutes of reaction (0-25% conversion), the toxicity of sulfur appears close to 1 the rates are proportional to the free surface. However, at higher conversion, the rate becomes independent from the sulfur ratio. The toxicity is zero. 

Initial and Final Sulfur Content of Palladium Catalyst Used in the I-Butyne Hydrogenation... 

The different toxicities found for 1-butene, 1,3-butadiene, and l-butyne hydrogenation can be explained by assuming that the energetic adsorption of unsaturated hydrocarbons destabilizes the metal-sulfur bond producing a real desulfurization with l-butyne. The destabilization exists also with the butadiene, as has been shown on platinum (71). 

In the liquid phase at room temperature, using alcohol as a solvent and palladium supported on barium sulfate as catalyst, the only products observed from 1-butyne hydrogenation were 1-butene (98%) and n-butane (2%) (57). The gas phase reaction using 0.03% palladium on alumina catalyst gave 1-butene (99.1%), cis- and product distributions were maintained until at least 76% removal of the parent hydrocarbon but isomerization and hydrogenation of the 1-butene occurred after complete removal of the alkyne. Thus, l-butjme must displace 1-butene from the surface before its isomerization can occur, and it must prohibit the re-entry of 1-butene into the reacting surface layer. This represents the operation of a powerful thermodynamic factor. 

The rate of l,4-dihydroxy-2-butyne hydrogenation was determined in the trickle phase with a 120-ml tubular reactor using 40 ml of either 3-mm activated tablets or hollow spheres. This hydrogenation was performed at 60 bar hydrogen pressure, 135°C, and the LHSV values of 0.80 and 1.6 h with a 50 wt.% 1,4-dihydroxy-2-butene aqueous solution whose pH was adjusted to 7 with NaHC03. 

Figure 12 Reaction scheme for l,4-dihydroxy-2-butyne hydrogenation.

Catalytic activities for butyne hydrogenation evidence effects due to particle size modifications, but also other effects necessitating a finer study of Mo Pd intaeractions. The modification of alumina by controlled molybdates deposition allows significant improvements in hydrogenation activities. 

As we found in our discussion of alkene stabilities (Section 11-5), heats of hydrogenation also provide convenient measures of the relative stabilities of alkyne isomers. In the presence of catalytic amounts of platinum or palladium on charcoal, the two isomers of butyne hydrogenate by addition of two molar equivalents of H2 to produce butane. Just as we discovered in the case of alkenes, hydrogenation of the internal alkyne isomer releases less energy, allowing us to conclude that 2-butyne is the more stable of the two. Hyperconjugation is the reason for the greater relative stabihty of internal compared with terminal alkynes. 

Prepared by heating ammonium mucate, or from butyne-l,4-diol and ammonia in the presence of an alumina catalyst. The pyrrole molecule is aromatic in character. It is not basic and the imino-hydrogen atom can be replaced by potassium. Many pyrrole derivatives occur naturally, e.g. proline, indican, haem and chlorophyll. 

Substituents affect the heats of hydrogenation of alkynes m the same way they affect alkenes Compare the heats of hydrogenation of 1 butyne and 2 butyne both of which give butane on taking up two moles of H2... 

Methylbutynol. 2-Methyl-3-butyn-2-ol [115-19-5] prepared by ethynylation of acetone, is the simplest of the tertiary ethynols, and serves as a prototype to illustrate their versatile reactions. There are three reactive sites, ie, hydroxyl group, triple bond, and acetylenic hydrogen. Although the triple bonds and acetylenic hydrogens behave similarly in methylbutynol and in propargyl alcohol, the reactivity of the hydroxyl groups is very different. 

The labile hydroxyl group is easily replaced by treatment with thionyl chloride, phosphorous chlorides, or even aqueous hydrogen haUdes. At low temperatures aqueous hydrochloric (186) or hydrobromic (187) acids give good yields of 3-halo-3-methyl-l-butynes. At higher temperatures these rearrange, first to l-halo-3-methyl-1,2-butadienes, then to the corresponding 1,3-butadienes (188,189). 

Diol Components. Ethylene glycol (ethane 1,2-diol) is made from ethylene by direct air oxidation to ethylene oxide and ring opening with water to give 1,2-diol (40) (see Glycols). Butane-1,4-diol is stiU made by the Reppe process acetylene reacts with formaldehyde in the presence of catalyst to give 2-butyne-l,4-diol which is hydrogenated to butanediol (see Acetylene-DERIVED chemicals). The ethynylation step depends on a special cuprous... 

Catalytic hydrogenation of alkynes on a metal surface provides cis alkenes (see Chapter 7, Problem 13), while treatment with sodium in liquid ammonia nearly always leads to trans alkenes, e.g., hydrogenation of 2-butyne. 

Finally, a special example of transition metal-catalyzed hydrogenation in which the ionic liquid used does not provide a permanent biphasic reaction system should be mentioned. The hydrogenation of 2-butyne-l,4-diol, reported by Dyson et al., made use of an ionic liquid/water system that underwent a reversible two-... 

The increase of selectivity in consecutive reactions in favor of the intermediate product may be sometimes extraordinarily high. Thus, for example, in the already cited hydrogenation of acetylene on a platinum and a palladium catalyst (45, 46) or in the hydrogenation or deuteration of 2-butynes on a palladium catalyst (57, 58), high selectivities in favor of reaction intermediates (alkenes) are obtained, even though their hydrogenation is in itself faster than the hydrogenation of alkynes. 

Hydrogenation reactions, particularly for the manufacture of fine chemicals, prevail in the research of three-phase processes. Examples are hydrogenation of citral (selectivity > 80% [86-88]) and 2-butyne-l,4-diol (conversion > 80% and selectivity > 97% [89]). Eor Pt/ACE the yield to n-sorbitol in hydrogenation of D-glucose exceeded 99.5% [90]. Water denitrification via hydrogenation of nitrites and nitrates was extensively studied using fiber-based catalysts [91-95]. An attempt to use fiber-structured catalysts for wet air oxidation of organics (4-nitrophenol as a model compound) in water was successful. TOC removal up to 90% was achieved [96]. 

This review covers the personal view of the authors deduced from the literature starting in the middle of the Nineties with special emphasis on the very last years former examples of structure-sensitive reactions up to this date comprise, for example, the Pd-catalyzed hydrogenation of butyne, butadiene, isoprene [11], aromatic nitro compounds [12], and of acetylene to ethylene [13], In contrast, benzene hydrogenation over Pt catalysts is considered to be structure insensitive [14] the same holds true for acetonitrile hydrogenation over Fe/MgO [15], CO hydrogenation over Pd [16], and benzene hydrogenation over Ni [17]. For earlier reviews on this field we refer to Coq [18], Che and Bennett [9], Bond [7], as well as Ponec and Bond [20]. 

In contrast, synthesis of 3,4-diphosphorylthiophenes requires more elaboration because of low reactivity of 3,4-positions of thiophene and unavailability of 3,4-dihalo or dimetallated thiophenes. Minami et al. synthesized 3,4-diphosphoryl thiophenes 16 as shown in Scheme 24 [46], Bis(phosphoryl)butadiene 17 was synthesized from 2-butyne-l,4-diol. Double addition of sodium sulfide to 17 gave tetrahydrothiophene 18. Oxidation of 18 to the corresponding sulfoxide 19 followed by dehydration gave dihydrothiophene 20. Final oxidation of 20 afforded 3,4-diphosphorylthiophene 16. 3,4-Diphosphorylthiophene derivative 21 was also synthesized by Pd catalyzed phosphorylation of 2,5-disubstituted-3,4-dihalothiophene and converted to diphosphine ligand for Rh catalysts for asymmetric hydrogenation (Scheme 25) [47],... 

---