Butadiene, selective polymerization

Various patents on the homopolymerization of BD in the presence of styrene are available [581-590]. According to these patents, St is used as a solvent in which BD is selectively polymerized by the application of NdV/DIBAH/EASC. At the end of the polymerization a solution of BR in St is obtained. In subsequent reaction steps the unreacted styrene monomer is either polymerized radically, or acrylonitrile is added prior to radical initiation. During the subsequent radical polymerization styrene or styrene/acrylonitrile, respectively, are polymerized and ris-l,4-BR is grafted and partially crosslinked. In this way BR modified (or impact modified) thermoplast blends are obtained. In these blends BR particles are dispersed either in poly(styrene) (yielding HIPS = high impact poly(styrene) or in styrene-acrylonitrile-copolymers (yielding ABS = acrylonitrile/butadiene/ styrene-terpolymers). In comparison with the classical bulk processes for HIPS and ABS, this new technology allows for considerable cost reductions... 

Rakova and Korotkov compared the rates of homopolymerization and copolymerization of styrene and butadiene [226], Styrene polymerizes very rapidly and butadiene slowly. Their copolymerization is slow at first, with preferential consumption of butadiene. When most of the butadiene is consumed, the reaction gradually accelerates yielding a product with a high styrene content. In the authors opinion, this is caused by selective solvation of the active centres by butadiene only after butadiene has polymerized, does styrene gain access to the centres [227], A similar behaviour was observed by Medvedev and his co-workes [228] and by many others. In our laboratory we observed this kind of behaviour in the cationic polymerization of trioxane with dioxolane. Although trioxane is polymerized much more rapidly than dioxolane, their copolymerization starts slowly, and is accelerated with progressing depletion of dioxolane from the monomer mixture [229],... 

Wang, D., Li, S.H., Liu, X.L. et al. (2008) Thiophene-NPN ligand supported rare-earth metal bis(alkyl) complexes. Synthesis and catalysis toward highly trans-1,4 selective polymerization of butadiene. Organometallics, 27, 6531. 

There are many possible schemes for addition reactions of diene monomers from electronical and steric viewpoints. Because the monomer molecules arrange along the direction of the channels, a,co-addition may selectively take place in one-dimensional inclusion polymerization. Therefore, conjugated polyenes, such as dienes and trienes, may selectively polymerize by 1,4- and 1,6-addi-tion, respectively. 1,3-Butadiene polymerized via 1,4-addition exclusively in the chaimels of urea and perhydrotriphenylene. while the same monomer polymerized via both 1,2- and 1,4-additions in the channels of deoxycholic acid and apocholic acid. Moreover, we have to evaluate head-to-tail or head-to-head (tail-to-tail) additions in the case of dissymmetric conjugated diene monomers such as isoprene and 1.3-pentadiene. 

By-products from EDC pyrolysis typically include acetjiene, ethylene, methyl chloride, ethyl chloride, 1,3-butadiene, vinylacetylene, benzene, chloroprene, vinyUdene chloride, 1,1-dichloroethane, chloroform, carbon tetrachloride, 1,1,1-trichloroethane [71-55-6] and other chlorinated hydrocarbons (78). Most of these impurities remain with the unconverted EDC, and are subsequendy removed in EDC purification as light and heavy ends. The lightest compounds, ethylene and acetylene, are taken off with the HCl and end up in the oxychlorination reactor feed. The acetylene can be selectively hydrogenated to ethylene. The compounds that have boiling points near that of vinyl chloride, ie, methyl chloride and 1,3-butadiene, will codistiU with the vinyl chloride product. Chlorine or carbon tetrachloride addition to the pyrolysis reactor feed has been used to suppress methyl chloride formation, whereas 1,3-butadiene, which interferes with PVC polymerization, can be removed by treatment with chlorine or HCl, or by selective hydrogenation. 

The process is characterized by high yield (nearly complete hydrogenation of acetylenes) and high selectivity (only a small loss of butadiene by hydrogenation). The process does not lead to polymerization, which might otherwise cause catalyst deactivation, and only infrequent regeneration of catalyst is necessary. 

Highly c/s-selectivity and low molecular weight distribution polymerization of l -butadiene with cobalt(II) pyridyl bis(imine) complexes in the presence of ethylaluminum sesquischloride effect of methyl position in the ligand... 

The 7r-back donation stabilizes the alkene-metal 7c-bonding and therefore this is the reason why alkene complexes of the low-valent early transition metals so far isolated did not catalyze any polymerization. Some of them catalyze the oligomerization of olefins via metallocyclic mechanism [25,30,37-39]. For example, a zirconium-alkyl complex, CpZrn(CH2CH3)(7/4-butadiene)(dmpe) (dmpe = l,2-bis(dimethylphosphino)ethane) (24), catalyzed the selective dimerization of ethylene to 1-butene (Scheme I) [37, 38]. 

The cycloadditions between tetrahalogenocyclopropenes and butadienes are usually carried out at about 100 °C in an inert solvent, in the presence of a small amount of K2CO3 and hydroquinone in order to prevent polymerization of the diene. Originally endo selectivity was assumed for additions of substituted open-chain dienes to 1,2-dihalogeno- and tetrahalogenocyclopropenes, but more recent X-ray and NMR investigations showed that the preferred mode of addition is exo. The cycloadducts are conveniently aromatized to cydoproparenes by reaction with r-BuOK in THF at low temperature. Since 1,1-dihalogenocyclo-proparenes solvolyze veiy readily, an anhydrous work-up procedure is usually indicated. 

---