Brunauer-Emmett-Teller adsorption

BET Brunauer-Emmett-Teller (adsorption isotherm) DPP differential pulse polarography... 

H. Brunauer-Emmett-Teller Adsorption isotherm Studies... 

A vast amount of research has been undertaken on adsorption phenomena and the nature of solid surfaces over the fifteen years since the first edition was published, but for the most part this work has resulted in the refinement of existing theoretical principles and experimental procedures rather than in the formulation of entirely new concepts. In spite of the acknowledged weakness of its theoretical foundations, the Brunauer-Emmett-Teller (BET) method still remains the most widely used procedure for the determination of surface area similarly, methods based on the Kelvin equation are still generally applied for the computation of mesopore size distribution from gas adsorption data. However, the more recent studies, especially those carried out on well defined surfaces, have led to a clearer understanding of the scope and limitations of these methods furthermore, the growing awareness of the importance of molecular sieve carbons and zeolites has generated considerable interest in the properties of microporous solids and the mechanism of micropore filling. 

In writing the present book our aim has been to give a critical exposition of the use of adsorption data for the evaluation of the surface area and the pore size distribution of finely divided and porous solids. The major part of the book is devoted to the Brunauer-Emmett-Teller (BET) method for the determination of specific surface, and the use of the Kelvin equation for the calculation of pore size distribution but due attention has also been given to other well known methods for the estimation of surface area from adsorption measurements, viz. those based on adsorption from solution, on heat of immersion, on chemisorption, and on the application of the Gibbs adsorption equation to gaseous adsorption. 

Specific surface area (SSA), total pore volume and average pore diameter were measured by N2 adsorption-desorption isotherms at 77K using Micromeritics ASAP 2020. The pore size was calculated on the adsorption branch of the isotherms using Barrett-Joyner-Helenda (BJH) method and the SSA was calculated using the Brunauer-Emmett-Teller (BET) method. 

Nitrogen adsorption was performed at -196 °C in a Micromeritics ASAP 2010 volumetric instrument. The samples were outgassed at 80 °C prior to the adsorption measurement until a 3.10 3 Torr static vacuum was reached. The surface area was calculated by the Brunauer-Emmett-Teller (BET) method. Micropore volume and external surface area were evaluated by the alpha-S method using a standard isotherm measured on Aerosil 200 fumed silica [8]. Powder X-ray diffraction (XRD) patterns of samples dried at 80 °C were collected at room temperature on a Broker AXS D-8 diffractometer with Cu Ka radiation. Thermogravimetric analysis was carried out in air flow with heating rate 10 °C min"1 up to 900 °C in a Netzsch TG 209 C thermal balance. SEM micrographs were recorded on a Hitachi S4500 microscope. 

Brunauer-Emmett-Teller (BET) adsorption describes multi-layer Langmuir adsorption. Multi-layer adsorption occurs in physical or van der Waals bonding of gases or vapors to solid phases. The BET model, originally used to describe this adsorption, has been applied to the description of adsorption from solid solutions. The adsorption of molecules to the surface of particles forms a new surface layer to which additional molecules can adsorb. If it is assumed that the energy of adsorption on all successive layers is equal, the BET adsorption model [36] is expressed as Eq. (6) ... 

The N2 adsorption-desorption isotherms for MSU-Ge-2 show a type-lV adsorption branch associated with a well-defined capillary condensation step at P/Po 0.13, characteristic of uniform mesopores (Fig. 4). The adsorption data indicate a very high Brunauer-Emmett-Teller (BET) surface area of 363 m /g and a pore volume of 0.23 cm /g. Given that the Ge mesostructure is much heavier than the corresponding silica, this surface area is actually equivalent to silica with a surface area of 1,316 m /g. 

Multilayer adsorption and the popular Brunauer-Emmett-Teller (BET) method of analysis are described in Section 9.5. This section also describes the determination of specific areas by gas adsorption. Low-temperature N2 adsorption and the BET method of analysis are so widely used for this purpose that these topics will receive special attention. 

EXAMPLE 9.5 Calculating the Adsorption Energy from the Brunauer-Emmett-Teller Isotherm. The BET analysis uses p/p0 rather than p as a variable just as we used this pressure ratio to compare Langmuir adsorption at different temperatures in Example 9.3. What corrections, if any, are needed in the apparent adsorption energy of about 14 kJ mole-1 as calculated in Example 9.3 ... 

Measurement of Surface Area. The Teachability determined by these methods is usually reported as g/cm day. The total surface area of particulate material can be assessed 1) by assuming a particle shape e.g.spherical) and estimating the number of particles, or 2) by measurements using the Brunauer-Emmett-Teller (BET) nitrogen adsorption technique ( ). Unfortunately, the BET method measures the area of surfaces to which nitrogen has access this is not necessarily the same as the area to which a solution has access. Access by solutions requires much larger pore areas. 

---