Aluminum charge

In the absence of any additive to the oxide-aluminum charge, it is necessary to attain a temperature of about 2200 °C to render the products molten and fit for gravity separation. The heat required for this purpose can be calculated as follows ... 

In practice, the production of vanadium by aluminothermic reduction is also governed by some other considerations. The reduction has to be carried out under an inert atmosphere (helium or argon) to avoid nitrogen pick-up from the air by vanadium metal. The composition of the oxide-aluminum charge has to be so chosen that the thermit (metal obtained by aluminothermic reduction) contains between 11 and 19% aluminum. This is necessary for the subsequent refining step in the vanadium metal production flowsheet. Pure vanadium pentoxide and pure aluminum are used as the starting materials, and the reduction is conducted in a closed steel bomb as shown in Figure 4.17 (C). 

The incorporation of aluminum increases the blast effect of explosives but decreases the rates of detonation, fragmentation effectiveness, and shaped charge performance. Mixes with aluminum are made by first screening finely divided aluminum, adding it to a melted RDX—TNT slurry, and stirring until the mix is uniform. A desensitizer and calcium chloride may be incorporated, and the mixture cooled to ca 85°C then poured. Typical TNT-based aluminized explosives are the tritonals (TNT + Al), ammonals (TNT, AN, Al), minols (TNT, AN, Al) torpexes and HBXs (TNT, RDX, Al) (Table 14) (223-226). 

Aluminum resinate particles, ie, size precipitate, are attracted to the fiber surfaces because of a difference in charge and thus are retained (45,46,54). In general, the particles of size precipitate are small and are distributed fairly uniformly over the sheet. However, on drying, there is some sintering of the particles which helps to redistribute them on the fibers. 

The use of alkali or alkaline-earth sulfides cataly2es the reaction so that it is complete in a few hours at 150—160°C use of aluminum chloride as the catalyst gives a comparable reaction rate at 115°C. When an excess of sulfur is used, the product can be distilled out of the reactor, and the residue of sulfur forms part of the charge in the following batch reaction. The reaction is carried out in a stainless steel autoclave, and the yield is better than 98% based on either reactant. Phosphoms sulfochloride is used primarily in the manufacture of insecticides (53—55), such as Parathion. 

Ion transport measurements indicate that Na" ions carry most of the current, yet aluminum is deposited. A charge transfer probably occurs at the cathode interface and hexafluoroaluminate ions are discharged, forming aluminum and F ions to neutralize the charge of the current carrying Na" ... 

There is much discussion on the nature of the aluminum species present in slightly acidic and basic solutions. There is general agreement that in solutions below pH 4, the mononuclear Al " exists coordinated by six water molecules, ie, [ ( 20) ". The strong positive charge of the Al " ion polarizes each water molecule and as the pH is increased, a proton is eventually released, forming the monomeric complex ion [A1(0H)(H20) ]. At about pH 5, this complex ion and the hexahydrated Al " are in equal abundance. The pentahydrate complex ion may dimerize by losing two water molecules... 

Commercial grades of socbum aluminate contain both waters of hycbation and excess socbum hycboxide. In solution, a high pH retards the reversion of socbum aluminate to insoluble aluminum hycboxide. The chemical identity of the soluble species in socbum aluminate solutions has been the focus of much work (1). Solutions of sodium aluminate appear to be totaby ionic. The aluminate ion is monovalent and the predominant species present is deterrnined by the Na20 concentration. The tetrahydroxyaluminate ion [14485-39-3], Al(OH) 4, exists in lower concentrations of caustic dehydration of Al(OH) 4, to the aluminate ion [20653-98-9], A10 2) is postulated at concentrations of Na20 above 25%. The formation of polymeric aluminate ions similar to the positively charged polymeric ions formed by hydrolysis of aluminum at low pH does not seem to occur. Al(OH) 4 has been identified as the predominant ion in dilute aluminate solutions (2). 

Water and Waste Water Treatment. PAG products are used in water treatment for removal of suspended soHds (turbidity) and other contaminants such as natural organic matter from surface waters. Microorganisms and colloidal particles of silt and clay are stabilized by surface electrostatic charges preventing the particles from coalescing. Historically, alum (aluminum sulfate hydrate) was used to neutralize these charges by surface adsorption of Al cations formed upon hydrolysis of the alum. Since 1983 PAG has been sold as an alum replacement in the treatment of natural water for U.S. municipal and industrial use. 

The simple picture of the MOS capacitor presented in the last section is compHcated by two factors, work function differences between the metal and semiconductor and excess charge in the oxide. The difference in work functions, the energies required to remove an electron from a metal or semiconductor, is = —25 meV for an aluminum metal plate over a 50-nm thermally grown oxide on n-ty e siUcon with n = 10 cm . This work... 

---