Absorbers optimization

Goudos, S.K. and Sahalos, J.N., Microwave absorber optimal design using multiobjective particle swarm optimisation, Microwave Optic. Tech. Letts., 48, 1553, 2006. 

Moreover, multivariate optimization, the simultaneous optimization of several properties, will increasingly come into focus. A drug should have high selectivity in binding to different receptors and minimal toxicity, good solubility and penetration, and so on. A hair color should have a brilliant shine, be absorbed well, not be washed out, not damage the hair, not be toxic, and be stable under sunlight, etc. 

One of the most effective ways to think about optimization is to visualize how a system s response changes when we increase or decrease the levels of one or more of its factors. A plot of the system s response as a function of the factor levels is called a response surface. The simplest response surface is for a system with only one factor. In this case the response surface is a straight or curved line in two dimensions. A calibration curve, such as that shown in Figure 14.1, is an example of a one-factor response surface in which the response (absorbance) is plotted on the y-axis versus the factor level (concentration of analyte) on the x-axis. Response surfaces can also be expressed mathematically. The response surface in Figure 14.1, for example, is... 

Onc-Factor-at-a-Timc Optimization One approach to optimizing the quantitative method for vanadium described earlier is to select initial concentrations for ITiOz and 1T2S04 and measure the absorbance. We then increase or decrease the concentration of one reagent in steps, while the second reagent s concentration remains constant, until the absorbance decreases in value. The concentration of the second reagent is then adjusted until a decrease in absorbance is again observed. This process can be stopped after one cycle or repeated until the absorbance reaches a maximum value or exceeds an acceptable threshold value. 

This experiment describes a fixed-size simplex optimization of a system involving four factors. The goal of the optimization is to maximize the absorbance of As by hydride generation atomic absorption spectroscopy using the concentration of HCl, the N2 flow rate, the mass of NaBH4, and reaction time as factors. 

In this experiment the goal is to mix solutions of 1 M HCl and 20-ppm methyl violet to give the maximum absorbance at a wavelength of 425 nm (corresponding to a maximum concentration for the acid form of methyl violet). A variable-size simplex optimization is used to find the optimum mixture. 

Single-reaction-step processes have been studied. However, higher selectivity is possible by optimizing catalyst composition and reaction conditions for each of these two steps (40,41). This more efficient utilization of raw material has led to two separate oxidation stages in all commercial faciUties. A two-step continuous process without isolation of the intermediate acrolein was first described by the Toyo Soda Company (42). A mixture of propylene, air, and steam is converted to acrolein in the first reactor. The effluent from the first reactor is then passed directiy to the second reactor where the acrolein is oxidized to acryUc acid. The products are absorbed in water to give about 30—60% aqueous acryUc acid in about 80—85% yield based on propylene. 

Eig. 3. Depiction of the light extraction, ie, escape cones of light emission, for various LED chip stmctures consisting of absorbing substrate devices having (a) thin window layers (top cone) (b) thick window layers (top cone and four one-half side cones) (c) thin window plus the implementation of a distributed Bragg reflector between the active layer and the substrate (top and bottom cone). Also shown is (d), the optimal stmcture for light extraction, a... 

A new cyanide dye for derivatizing thiols has been reported (65). This thiol label can be used with a visible diode laser and provide a detection limit of 8 X 10 M of the tested thiol. A highly sensitive laser-induced fluorescence detector for analysis of biogenic amines has been developed that employs a He—Cd laser (66). The amines are derivatized by naphthalenedicarboxaldehyde in the presence of cyanide ion to produce a cyanobenz[ isoindole which absorbs radiation at the output of He—Cd laser (441.6 nm). Optimization of the detection system yielded a detection limit of 2 x 10 M. 

Dmg loading can be accompHshed by dispersion or adsorption. In dispersed systems, a dmg is blended into a polymer by mechanical means, such as a kneader. The viscosity of the polymer, and the size and concentration of the dmg, need to be optimized to minimize aggregates. Dmgs can also be absorbed by equiUbrating a polymer in a dmg solution. The absorption rate can be accelerated by introducing an appropriate solvent to swell the polymer. AH solvents would then have to be removed. 

This section is a companion to the section titled Fractionators-Optimization Techniques. In that section the Smith-Brinkley method is recommended for optimization calculations and its use is detailed. This section gives similar equations for simple and reboiled absorbers. 

---