Transition metals analytical techniques

Hafnium metal is analy2ed for impurities using analytical techniques used for 2irconium (19,21,22). Carbon and sulfur in hafnium are measured by combustion, followed by chromatographic or in measurement of the carbon and sulfur oxides (19). Chromatographic measurement of Hberated hydrogen follows the hot vacuum extraction or fusion of hafnium with a transition metal in an inert atmosphere (23,24). 

Certain transition metal salts can be used as radical traps (Scheme 3.89, Scheme 3.90).486 These include various cupric (e.g. Cu(OAc)2, CuCl , Cu(SCN)i),l8 1<,8 J< 3 432 487 ferric (e.g. FeCli),316 488 and titanotis salts (eg. TiCL,).379 These traps react with radicals by ligand- or electron-transfer to give products which can be determined by conventional analytical techniques. 

Transamidation, polyamide, 158 Transesterification, 529-530 Transesterification polymerizations, 69-74 Transimidization, 302-303 Transition metal coupling, 10, 467-523 applications for, 472-476 chemistry and analytic techniques for, 483-490... 

A potentially interesting development is the microwave-assisted transition-metal-free Sonogashira-type coupling reaction (Eq. 4.10). The reactions were performed in water without the use of copper(I) or a transition metal-phosphine complex. A variety of different aryl and hetero-aryl halides were reactive in water.25a The amount of palladium or copper present in the reaction system was determined to be less than 1 ppm by AAS-MS technique. However, in view of the recent reassessment of a similarly claimed transition-metal-free Suzuki-type coupling reaction, the possibility of a sub-ppm level of palladium contaminants found in commercially available sodium carbonate needs to be ruled out by a more sensitive analytical method.25 ... 

The participation of cations in redox reactions of metal hexacyanoferrates provides a unique opportunity for the development of chemical sensors for non-electroactive ions. The development of sensors for thallium (Tl+) [15], cesium (Cs+) [34], and potassium (K+) [35, 36] pioneered analytical applications of metal hexacyanoferrates (Table 13.1). Later, a number of cationic analytes were enlarged, including ammonium (NH4+) [37], rubidium (Rb+) [38], and even other mono- and divalent cations [39], In most cases the electrochemical techniques used were potentiometry and amperometry either under constant potential or in cyclic voltammetric regime. More recently, sensors for silver [29] and arsenite [40] on the basis of transition metal hexacyanoferrates were proposed. An apparent list of sensors for non-electroactive ions is presented in Table 13.1. 

The use of IAECL for analytical applications has now almost entirely been surpassed by techniques based on certain transition metal complexes, from which ECL reactions can occur in aqueous solution. 

Many transition metal complexes have been considered as synzymes for superoxide anion dismutation and activity as SOD mimics. The stability and toxicity of any metal complex intended for pharmaceutical application is of paramount concern, and the complex must also be determined to be truly catalytic for superoxide ion dismutation. Because the catalytic activity of SOD1, for instance, is essentially diffusion-controlled with rates of 2 x 1 () M 1 s 1, fast analytic techniques must be used to directly measure the decay of superoxide anion in testing complexes as SOD mimics. One needs to distinguish between the uncatalyzed stoichiometric decay of the superoxide anion (second-order kinetic behavior) and true catalytic SOD dismutation (first-order behavior with [O ] [synzyme] and many turnovers of SOD mimic catalytic behavior). Indirect detection methods such as those in which a steady-state concentration of superoxide anion is generated from a xanthine/xanthine oxidase system will not measure catalytic synzyme behavior but instead will evaluate the potential SOD mimic as a stoichiometric superoxide scavenger. Two methodologies, stopped-flow kinetic analysis and pulse radiolysis, are fast methods that will measure SOD mimic catalytic behavior. These methods are briefly described in reference 11 and in Section 3.7.2 of Chapter 3. 

After Faraday s seminal report on the preparation of transition metal clusters in the presence of stabilizing agents in 1857 [31], Turkevich [19-21] heralded the first reproducible protocol for the preparation of metal colloids and the mechanism proposed by him for the stepwise formation of nanoclusters based on nucleation, growth, and agglomeration [19] is still valid but for some refinement based on additional information available from modem analytical techniques and data from thermodynamic and kinetic experiments [32-41], Agglomeration of zero-valent nuclei in the seed or, alternatively, collisions of already formed nuclei with reduced metal atoms are now considered the most plausible mechanism for seed formation. Figure 3.1 illustrates the proposed mechanism [42],... 

Applications of electrospray mass spectrometry (ESMS) to the study of reactions mediated by transition-metal complexes are reviewed. ESMS has become increasingly popular as an analytical tool in inorganic and organometallic chemistry, in particular with regard to the identification of short-lived intermediates of catalytic cycles. Going one step further, the coupling of electrospray ionization to ion-molecule techniques in the gas phase yields detailed information about single reaction steps of catalytic cycles. This method allows the study of transient intermediates that have previously not been within reach of condensed-phase techniques on both a qualitative and quantitative level. 

Polarography (discovered by Jaroslav Heyrovsky in 1922) is a technique in which the potential between a dropping mercury electrode and a reference electrode is slowly increased at a rate of about 50 200 mV min while the resultant current (carried through an auxihary electrode) is monitored the reduction of metal ions at the mercury cathode gives a diffusion current proportional to the concentration of the metal ions. The method is especially valuable for the determination of transition metals such as Cr, Mn, Fe, Co, Ni, Cu, Zn, Ti, Mo, W, V, and Pt, and less than 1 cm of analyte solution may be used. The detection hmit is usually about 5 X 10 M, but with certain modifications in the basic technique, such as pulse polarography, differential pulse polarography, and square-wave voltammetry, lower limits down to 10 M can be achieved. 

---