Tables of basic allowances

A credit consists of a notification to a Headquarters that specific items are available in definite quantities in a specified depot subject to requisition [draft by the Headquarters for whom the credit is established. Materials which have been credited to a Headquarters may be withdrawn at the discretion of the using Headquarters without reference to Tables of Basic Allowances or Tables of Allowances. In CWS ETO Sup Circ Ltr i, 30 Jul 41. CWS ETO 300.4/1 (a6-7-4i)SD. In ETO Admin f45A. 

The CWS in SWPA was not yet aware, at the end of June, of the War Department supply policy they had heard nothing at all from the United States in the first four months after the establishment of the USAFIA and were to have no word from the Office of the Chief, Chemical Warfare Service, until July. The basic War Department plan was dated 22 January 1942, and the specific plan for the forces in Australia was dated 2 February 1942. The specific War Department plan called for 90 days supply of all classes other than ammunition, computed on the standard tables of basic allowances (TBA) 90 days supply of ground ammunition, computed on the basis of a special ammunition day of supply for weapons in the theater and five months supply of aerial bombs, ammunition, and pyrotechnics, computed according to a special allowance per aircraft in Australia and the Netherlands East Indies. The Adjutant General instructed the technical services in the United States to compute allowances and set up shipments to the San Francisco Port of Embarkation, which was charged with shipment to the theater. The chiefs of the technical services were also charged with allotting funds to the theater for the operation of their services in the theater and for the local procurement of materiel. ... 

GAS MASKS.-<. The training allowances of gas masks are governed by Tables of Basic Allowances, 1939, or later revisions. 

To the maximum extent possible, all instruction will be practical rather than theoretical. Simulated materials available locally will be used to supplement the training munitions and supplies authorized by AR 775-10., Tables of Allowances, and Tables of Basic Allowances. 

The SE values in Table 10-49 are equal to the basic allowable stresses in tension S multiplied by a quality factor E (see subsection Pressure Design of Metallic Components Wall Tliick-ness"). The design stress values for bolting materials are equal to die basic allowable stresses S. The stress values in shear shall be 0.80 times the allowable stresses in tension derived from tabulated values in Table 10-49 adjusted when applicable in accordance widi Note 13. 8tress values in bearing shall be twice those in shear. 

It should be noted that Table 14.1 presents the most simple variants of inhibitory mechanisms with a minimal set of basic reactions. In practice, the dependancies of F may be more complex. However, the function F allows the mechanism of the inhibitory action of antioxi-... 

The detailed synthesis procedure and textural properties (surface area, Sggy in m2 g-1 pore volume, V in ml g"1 and main pore diameter, d in nm), determined by nitrogen adsorption from 8.E.T. method have been published elsewhere (refs. 13-18) and are summarized in Table 1, where the surface acidity and basicity of supports are also collected. These values were determined by a spectro-photometric method described elsewhere (ref. 19), that allows titration of the amount (in tunol g 1) of irreversibly adsorbed benzoic acid (BA, pKa> 4.19), pyridine (PY, pka= 5.25) or 2,6-diterbutyl-4-methylpyridine (DTMPY, pKa 7.5) employed as titrant agents of basic and acid sites, respectively. Furthermore, the apparent rate constant values of different supports in the gas-phase skeletal isomerization of cyclohexene (CHSI), in Mmol atm"1 g"1 s-1, at 673 K, are also collected in Table 1, because these values are another way of measuring the stronger acid sites of supports (ref. 19). 

The non-basic nature of the reagent makes it useful in other applications. It has, for example, also proved useful for the methylenation of the gibberelUn norketone4 (Table I) without the need for protection of the readily epimerized 3B-0H. The use of CD2Br24 allows the introduction of =C02 without scrambling of the label. 

The Quantitative section measures your general understanding of basic high school mathematical concepts. You will not need to know any advanced mathematics. This test is a simple measure of your availability to reason clearly in a quantitative setting. Therefore, you will not be allowed to use a calculator on this exam. Many of the questions are posed as word problems relating to real-life situations. The quantitative information is given in the text of the questions, in tables and graphs, or in coordinate systems. 

Table 13.4 allows for a comparison of the basicities of the strongest lithium-containing bases. The basicities are measured by the heats of deprotonation liberated upon mixing the reference acid isopropanol with these bases. These heats of deprotonation reveal that organo-lithium compounds are even stronger bases than lithium amides. Their basicities decrease from te/7-BuLi via. sec-BuLi and w-BuLi to PhLi. 

There are various ways to compare structures and, more specifically, to list the relevant differences between computed and experimental structural data (i) you can use the Overlay module in the ChemPlus extension of HyperChem (Overlay in the basic version of HyperChem does not provide rms differences and thus is not useful for parameter fitting) (ii) we suggest that you make a table of the relevant parameters (iii) the developers kit in HyperChem 5.0 allows for coupling HyperChem with external programs, such as Excel , and this may facilitate the production and analysis of such tables. 

The core instructions used in programs MSD, CORREL, FACTORS, HISTO, and MULTI are given in a stripped-down version of BASIC in the following tables to allow the reader to follow the ideas from a different vantage point and/or to migrate the program kernels to a programmable calculator. Numerical examples are provided to check the calculations. 

---