Subject ultimate strength

A process may suffer destruction but be isolated from the public by containment. H the containment may fail from pressure, heat and missiles - the subject of containment eve These analyses determine yield and ultimate-strength levels for the base structure. If the ultimate strength of a thin-shell stmcture is determined quite simply, the results may not be v )f... 

The treated phenomena and investigations summarized above are at the centre of the topic of this special two-volume edition of the Advances in Polymer Science on Intrinsic molecular mobility and toughness of polymers . However, little has been said about the mutual relations between molecular configuration, polymer morphology, nature, intensity and cooperativity of sub-Tg relaxation mechanisms, and mode of solicitation on the one hand and their effect on disentanglement, craze formation, yield behaviour and ultimate strength on the other. These subjects will be critically evaluated in the subsequent presentations of this Volume. 

Creep is the term used to describe the tendency of a material to move or to deform permanently to relieve stresses. Material deformation occurs as a result of long term exposure to levels of stress (physics) that are below the yield strength or ultimate strength of the material. Creep is more severe in materials that are subjected to heat for long periods and near melting point. Creep is often observed in glasses. Creep is a monotonically increasing function of temperature. 

Portland cement clinker normally contains not more than about 0.2% P2O5, and further small additions to anhydrous portland cement before hydration and setting are reported to inaease the hardening rate and the ultimate strength. Larger additions (certainly >1.0%) have a retarding effect and can have disastrous results, but the subject is somewhat controversial [37,38]. 

Ultimate strength n. The maximum nominal stress a material can withstand when subjected to an applied tensile, compressive, or shear load. If the mode of loading is not specified, it is assumed to be tensile. In materials that exhibit a definite yield strength, ultimate strength will usually mean the nominal stress at break, which can be less than the maximum. Shah V (1998) Handbook of plastics testing technology. John Wiley and Sons, New York. 

Answer by author The reasons for the rather abrupt change in ductility and ultimate strength, as related to the phase transformation, are not clear at present. It is interesting to note that a transitional hexagonal close packed phase is also present upon straining at low temperatures. However, we will submit more experimental data concerning this subject later. ... 

Fatigue (Structural) The progressive localized permanent structural change that occurs in a material subjected to constant or variable amplitude loads at stresses having a maximum value less than the ultimate strength of the material. 

Crossland, B., and Bones, J. A., The Ultimate Strength of rhick-walled Cylinders Subjected to Internal Pressure, Engineering, January, 1955, pp. 80-83 and 114-117. Manning, W. R. D., The Overstrain of Tubes by Internal Pressure, Engineering, 159 (ifiB), pp. 101 10 183... 

Hot melt adhesives, another class of one-part systems, produce excellent adhesion. These adhesives reach their ultimate strength seconds after application but may lose their strength at temperatures below -18° C (0°F) or above 93° C (200° F). Some are also subject to cold flow under prolonged heavy loading. However, their resistance to hot water is excellent . 

Tensile Ultimate Strength n the maximum tensile stress subjected to the test specimen during the tensile test. The value can be identical with the tensile stress at break. 

Moisture has an effect, but its influence may only be significant if components are either highly stressed compared with their ultimate strength or used at temperatures close to the heat distortion temperature of the resin. If either condition is applicable then measurements will be needed to determine the safety factor of the design. BS 5480 recommends an operating temperature of at least lO C below the HDT of the resin for components subject to prolonged exposure to stress. 

What do we want the adhesive to do for us Start by listing all of the requirements expected of the adhesive formulation the drying time, the ultimate strength needed in the bonded assembly, the years of service expected, the conditions to which the bonded assembly will be subjected, etc. 

Ultimate Strength. The maximum unit stress a material will withstand when subjected to an applied load in compression, tension, or shear. This is expressed in Ib/in.. ... 

Tensile strength Ultimate strength of a material subjected to tensile loading. 

---