Sorption processes concentration effects

The presence of suspended solid materials increases the extent of LAS biodegradation [13,28], but the rate of the process remains invariable. The influence of the particulate material is due specifically to the increased density of the microbiota associated with sediments. However, suspended solids may also reduce the bioavailability of IAS as a result of its sorption onto preferential sites (e.g. clays, humic acids), although this is a secondary effect due to the reversibility of the sorption process. Salinity does not affect IAS degradation directly, but could also reduce LAS bioavailability by reducing the solubility of this molecule [5], Another relevant factor to be taken into account is that biodegradation processes in the marine environment could be limited by the concentration of nutrients, especially of phosphorus and nitrogen [34],... 

For sorption/desorption studies, the sorption reaction is followed by monitoring the increasing concentration of leachate with time. At an apparent equilibrium, the effluent concentration equals that of the initial sorptive solution. The desorption reaction is studied in a similar way, the reaction being followed by monitoring the decreasing concentration of the previously sorbed ion or other sorbate. In either case, the reaction is followed by determining the sorptive concentration in solution. This means that any process that effects a change in concentration will be interpreted as adsorption or desorption. 

Several common local sorption processes have been examined here by way of illustrating such effects sorption by geologically immature soft-carbon organic matter, which results in quasi-linear sorption isotherms, sorption by common mineral phases within concentration regions where linear behavior is exhibited, and sorption by diagenetically altered hard-carbon organic matter... 

The evaluation of the sorption conditions, using the Armstrong-Stannett treatment of the effect of the heat of sorption on the measured diffusion constant, clearly shows that the sorption process, at even moderate concentrations, is no longer isothermal. 

Sorption processes are very effective and include adsorption/desorption (reversible binding at the solid-water interface), absorption (diffusion of pollutants into the solid matrix), precipitation and coprecipitation (incorporation into a freshly formed solid), and occlusion (sequestration of adsorbed pollutants during mineral growth). The most important factors for retention processes are pollutant concentration, the composition of the solid matrix, solution composition (e.g., complexing agents) and E/pH conditions (Brady and Boms 1997). 

Of particular importance is the timescale over which diffusion occurs under various conditions of relative humidity (RH) and temperature. The RH determines the equilibrium moisture concentration, whereas higher temperatures will accelerate the moisture sorption process. In order to predict the moisture profile in a particular structure, it is assumed that Fickian diffusion kinetics operate. It will be seen later that many matrix resins exhibit non-Fickian effects, and other diffusion models have been examined. However, most resin systems in current use in the aerospace industry appear to exhibit Fickian behaviour over much of their service temperatures and times. Since the rate of moisture diffusion is low, it is usually necessary to use elevated temperatures to accelerate test programmes and studies intended to characterize the phenomenon. Elevated temperatures must be used with care though, because many resins only exhibit Fickian diffusion within certain temperature limits. If these temperatures are exceeded, the steady state equilibrium position may not be achieved and the Fickian predictions can then be inaccurate. This can lead to an overestimate of the moisture absorbed under real service conditions. 

The catalytic dehydration of isopropanol was studied under tiansirat conditimis in a catalytic microreactor. The reaction is characterised by educt inhibition and shows a pronounced stop-effect . Therefore, the average productivity under forced poiodic operation can be considerably higher compared to the maximal productivity obtainable at steady state. For high rates of the sorption processes and surface reactions involved, the timal cycle time for the forced concentration variations lies in the order of seconds. As microreactors are characterized by low mass storage capacity and narrow residence time distribution, they are particularly suitable for periodic operation at relatively high fiequencies. Tis could be demonstrated in the present study. 

While the occurrence of most processes affecting organophosphorus insecticide concentrations in surface runoff are well documented, many are relatively poorly understood on a mechanistic level. Key processes requiring further study include sorption to plant and soil surfaces, and transfer from soil water into overland flow. Sorption to foliar surfaces determines the amount of applied insecticide available for washoff onto the soil surface or into surface runoff The kinetics of desorption from plant cuticular materials and the effect of adjuvants on foliar sorption processes need additional research. 

Cooperative effects are of considerable interest for high capacity chromatography of BAS, since for practical purposes high-selectivity bonding is possible only in cooperative processes. This is very important for carrying out the sorption, separation and concentration of BAS. 

Phenanthrene dissolved in Triton X-100 solution was separated by sorption with three GACs with different particle size (4 12,12 20, and 20 40 mesh). The highest adsorption selectivity was obtained with the 20 40 mesh over a wide concentration range of phenanthrene and Triton X-100. The results demonstrate that the selective adsorption is potentially effective to reuse surfactants in a soil-washing process for the remediation of contaminated soils. 

---