Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Signal validation

Fig. 3.1. Chemical measurement process (above) and information process (below) 1 Measurement, 2 Signal validation, 3 Evaluation/calibration, 4 Data evaluation, A Coding, B Selection, C Decoding, data evaluation... [Pg.70]

Signal validation Signal validation routines are supported in most of the DCS/PLC family. Signal validation routines allow for the control of one logical input produced from up to four redundant inputs (three hardware and one additional logic) [8]. [Pg.824]

For clutter suppression, the test statistic used by the noncoherent detector has been proposed as an interesting output signal [1], This was motivated by the fact that, provided that transient and noise models are valid, the test statistic reflects the likelihood that a transient is present. [Pg.90]

Before starting the realisation of silicium coils, we construct a simpler probe with a 27 mm long excitation coil and 16 wired coil sensors, with 1 mm diameter and 1 mm long. We cannot hope any reconstruction with such a probe, but this allows to validate the whole approach. We tried it with test tubes with longitudinal or circonferential notches, external or internal, 100 pm wide, 100%, 60%, 40%, 20% and 10% deep. Our attention has been especially focused on circonferential notches, which are difficult to detect with usual probes. For example, the measurement signals at 240 kHz standard frequency are shown figure 6 7. [Pg.359]

The measurements are put together of discrete measured points. Then the superposition integral valid for continuous signals changes into a superposition addition for discrete signals ... [Pg.367]

The results obtained by lineal regression (LR) and by pareial least square regression (PLS) methods have been eompared to quantify tlie 0-H signal in anhydrite samples. The PLS quality is eharaeterized by a eoirelation eoeffieient of 0.9942 (eross-validation) using four faetors and a root mean square eiTor of ealibration (RMSEC) of 0.058. Tlie eoirelation eoeffieient of LR metliod obtained was 0.9753. [Pg.200]

A further example where quantitative surface composition analysis is possible for a non-trivial surface is shown in Fig. 3.58, where for the systems Ta -i- O and Nb -i- O adsorption the ion signal from the metal is shown as a function of the ion signal from O. In this binary example Eq. (3.43) are valid for the concentration ... [Pg.156]

In addition, vibration data collected with a microprocessor-based analyzer is filtered and conditioned to eliminate non-recurring events and their associated vibration profiles. Anti-aliasing filters are incorporated into the analyzers specifically to remove spurious signals such as impacts. While the intent behind the use of anti-aliasing filters is valid, however, their use can distort a machine s vibration profile. [Pg.699]

The different reactivity mentioned above also proves the validity of inequality ki, k3> >k4 used in the simplification of our model. On the contrary, in the presence of CHA less than one equivalent the signals of both the la and Ih appear, a large extent of deuteration at C-3 is observed both in the cis and tram isomers and in the product flavone (2). Using an excess of amine both isomer gave 2 deuterated at C-3 to an extent ca. 80-85 %. Considering the kinetic profile of the interconversion we conclude that it takes place via an enolate where the rate determining step is the deprotonation at C-3. [Pg.276]

Critical ( -values for p - 0.05 are available. " - In lieu of using these tables, the calculated -values can be divided by the appropriate Student s t(f, 0.05) and V2 and compared to the reduced critical -vdues (see Table 1.12), and data file QRED TBL.dat. A reduced -value that is smaller than the appropriate critical value signals that the tested means belong to the same population. A fully worked example is found in Chapter 4, Process Validation. Data file MOISTURE.dat used with program MULTI gives a good idea of how this concept is applied. MULTI uses Table 1.12 to interpolate the cutoff point for p = 0.05. With little risk of error, this table can also be used fo = 0.025 and 0.1 (divide q by t(/, 0.025) /2 respectively t f, 0.1) V 2, as appropriate. [Pg.57]


See other pages where Signal validation is mentioned: [Pg.40]    [Pg.14]    [Pg.408]    [Pg.359]    [Pg.379]    [Pg.103]    [Pg.40]    [Pg.14]    [Pg.408]    [Pg.359]    [Pg.379]    [Pg.103]    [Pg.37]    [Pg.38]    [Pg.44]    [Pg.106]    [Pg.158]    [Pg.329]    [Pg.444]    [Pg.655]    [Pg.751]    [Pg.770]    [Pg.884]    [Pg.889]    [Pg.50]    [Pg.119]    [Pg.770]    [Pg.2576]    [Pg.36]    [Pg.44]    [Pg.486]    [Pg.230]    [Pg.155]    [Pg.214]    [Pg.184]    [Pg.915]    [Pg.1030]    [Pg.137]    [Pg.240]    [Pg.44]    [Pg.156]    [Pg.175]    [Pg.24]   
See also in sourсe #XX -- [ Pg.44 ]

See also in sourсe #XX -- [ Pg.44 ]




SEARCH



Data-driven Validation of Templates in Signal Events

© 2024 chempedia.info