Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Requirements of a Good Bond

In commercial practice, powdered explosives on an ammonium nitrate basis are used in most cases. Typical detonation velocities are between 1800 and 3500 m/s depending on the metal system to be bonded. The lower detonation velocity range is preferred for many metal systems in order to minimize the quantity of solidified melt associated with the bond-zone waves (12). In addition, subsonic detonation velocity explosives are required for the parallel cladding technique in order to avoid attached shock waves in the coUision region, which preclude formation of a good bond. [Pg.148]

The basic requirements for a good bond to plastic substrates are surface cleanliness, wetting of the surface by the adhesive, solidification of the adhesive, and proper selection of adhesive and joint design. These requirements are briefly defined here and then more thoroughly discussed in following sections. [Pg.432]

Various theories attempt to describe the phenomena of adhesion. No single theory explains adhesion in a general way. However, knowledge of adhesion theories can assist in understanding the basic requirements for a good bond. [Pg.402]

The blending of PPO and polyamides requires special grafting techniques to give a good bond between the two polymers, as otherwise the two polymers are incompatible. Whilst these polymers show the good dimensional stability and toughness of styrenic PPOs, they also have... [Pg.592]

The heuristic value of equation (3) is that we can see what is required for a good initiator D and I(R ) must be as large a possible, and AHS(R+) should be small compared to AHS(RI>1+) in other words, as an efficient initiator we need a large cation whose parent radical has a high ionisation potential, and which forms a strong bond to monomer. On the last two counts the trityl cation must be one of the least suitable. These considerations indicate that the first four ions listed in Table 1 should merit detailed study as initiators for vinyl polymerisations. [Pg.212]

In the second step the bas is recognized by the receptor site and the bas-rep complex forms. As was noted above, the complex is generally bonded by inter-molecular forces. The bas is transferred from an aqueous phase to the receptor site. The receptor site is very much more hydrophobic than is the aqueous phase. It follows, then, that complex formation depends on the difference in intermolecular forces between the bas-aqueous phase and the bas-receptor site. The importance of a good fit between bas and receptor site has been known for many years. The configuration and conformation of the bas can be of enormous importance. Also important is the nature of the receptor. If the receptor is. a cleft, as is the case in some enzymes, steric effects may be maximal as it may not be possible for a substituent to relieve steric strain by rotating into a more favorable conformation. In such a system, more than one steric parameter will very likely be required in order to account for steric effects in different directions. Alternatively, the receptor may resemble a bowl, or a shallow, fairly flat-bottomed dish. Conceivably it may also be a mound. In a bowl or dish, steric effects are likely to be very different from those in a cleft. Possible examples are shown in Fig. 1, 2, and 3. [Pg.5]


See other pages where Requirements of a Good Bond is mentioned: [Pg.4]    [Pg.370]    [Pg.405]    [Pg.7]    [Pg.4]    [Pg.4]    [Pg.370]    [Pg.405]    [Pg.7]    [Pg.4]    [Pg.787]    [Pg.203]    [Pg.787]    [Pg.539]    [Pg.18]    [Pg.56]    [Pg.419]    [Pg.537]    [Pg.4]    [Pg.363]    [Pg.229]    [Pg.450]    [Pg.349]    [Pg.185]    [Pg.259]    [Pg.329]    [Pg.247]    [Pg.31]    [Pg.18]    [Pg.105]    [Pg.604]    [Pg.318]    [Pg.235]    [Pg.220]    [Pg.165]    [Pg.168]    [Pg.1475]    [Pg.151]    [Pg.22]    [Pg.700]    [Pg.82]    [Pg.12]    [Pg.201]    [Pg.311]    [Pg.544]    [Pg.544]    [Pg.190]   


SEARCH



Bonds requirements

© 2024 chempedia.info