Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Pascal-second

Pound-second per square inch pascal-second 6894.76... [Pg.123]

Poundal-second per square foot pascal-second 1.488 164... [Pg.123]

The SI unit of viscosity is pascal-second (Pa s) or newton-second per meter squared (N s m ). Values tabulated are mN s (= centipoise, cP). The temperature in degrees Celsius at which the viscosity of a... [Pg.449]

The dynamic viscosity, or coefficient of viscosity, 77 of a Newtonian fluid is defined as the force per unit area necessary to maintain a unit velocity gradient at right angles to the direction of flow between two parallel planes a unit distance apart. The SI unit is pascal-second or newton-second per meter squared [N s m ]. The c.g.s. unit of viscosity is the poise [P] 1 cP = 1 mN s m . The dynamic viscosity decreases with the temperature approximately according to the equation log rj = A + BIT. Values of A and B for a large number of liquids are given by Barrer, Trans. Faraday Soc. 39 48 (1943). [Pg.496]

Viscosity is equal to the slope of the flow curve, Tf = dr/dj. The quantity r/y is the viscosity Tj for a Newtonian Hquid and the apparent viscosity Tj for a non-Newtonian Hquid. The kinematic viscosity is the viscosity coefficient divided by the density, ly = tj/p. The fluidity is the reciprocal of the viscosity, (j) = 1/rj. The common units for viscosity, dyne seconds per square centimeter ((dyn-s)/cm ) or grams per centimeter second ((g/(cm-s)), called poise, which is usually expressed as centipoise (cP), have been replaced by the SI units of pascal seconds, ie, Pa-s and mPa-s, where 1 mPa-s = 1 cP. In the same manner the shear stress units of dynes per square centimeter, dyn/cmhave been replaced by Pascals, where 10 dyn/cm = 1 Pa, and newtons per square meter, where 1 N/m = 1 Pa. Shear rate is AH/AX, or length /time/length, so that values are given as per second (s ) in both systems. The SI units for kinematic viscosity are square centimeters per second, cm /s, ie, Stokes (St), and square millimeters per second, mm /s, ie, centistokes (cSt). Information is available for the official Society of Rheology nomenclature and units for a wide range of rheological parameters (11). [Pg.167]

L, viscosity to convert pascal-seconds to pound-force-seconds per square foot, multiply by 0.020885 to convert pascal-seconds to Cp, multiply by 1000. [Pg.249]

Thermal conductivity to convert watts per meter-kelvin to British thermal unit-feet per hour-square foot-degree Fahrenheit, multiply by 0.57779 and to convert British thermal unit-feet per hour-square foot-degree Fahrenheit to watts per meter-kelvin, multiply by 1.7307. Viscosity to convert pascal-seconds to centipoises, multiply by 1000. [Pg.362]

F — 32)/1.8 to convert British thermal units per hoiir-sqiiare foot-degrees Fahrenheit to joules per square meter-second-kelvins, multiply by 5.6783 to convert centipoises to pascal-seconds, multiply hy 10 . ... [Pg.1047]

FIG. 14-7 O Connell correlation for overall column efficiency for absorption. To convert ffP/ i in pound-moles per cubic foot-centipoise to Idlogram-moles per cubic meter-pascal-second, multiply by 1.60 X 10 . [O Connell, Trans. Am. Inst. Chem. Eng., 42, 741 (1946).]... [Pg.1358]

An unreconstructed cgs er messed up your viscosity correlation by reporting his results in centipoise rather than pascal seconds. How does this affect the sample velocity profile calculated in Example 8.10 What does the term unreconstructed cgs er mean ... [Pg.308]

Figure 7.1. Uptake curves for first and second order adsorption as a function of gas dose given in Pascal seconds. In this example, the sticking coefficient is strongly activated, with an activation energy of 60 kj moTb... Figure 7.1. Uptake curves for first and second order adsorption as a function of gas dose given in Pascal seconds. In this example, the sticking coefficient is strongly activated, with an activation energy of 60 kj moTb...
Figure A-4 Nomograph for viscosities of liquids at 1 atm. See Table A-1 for coordinates. (To convert centipoise to pascal-seconds, multiply by 0.001.)... Figure A-4 Nomograph for viscosities of liquids at 1 atm. See Table A-1 for coordinates. (To convert centipoise to pascal-seconds, multiply by 0.001.)...
Figure A-5 Nomograph for determining absolute viscosity of a gas near ambient pressure and relative viscosity of a gas compared with air. (Coordinates from Table A-7.) To convert from poise to pascal-seconds, multiply by 0.1. (From Beerman, Meas Control, June 1982, pp 154-157.)... Figure A-5 Nomograph for determining absolute viscosity of a gas near ambient pressure and relative viscosity of a gas compared with air. (Coordinates from Table A-7.) To convert from poise to pascal-seconds, multiply by 0.1. (From Beerman, Meas Control, June 1982, pp 154-157.)...

See other pages where Pascal-second is mentioned: [Pg.112]    [Pg.114]    [Pg.122]    [Pg.123]    [Pg.123]    [Pg.124]    [Pg.125]    [Pg.564]    [Pg.23]    [Pg.630]    [Pg.362]    [Pg.362]    [Pg.1388]    [Pg.1393]    [Pg.1394]    [Pg.1394]    [Pg.1394]    [Pg.1394]    [Pg.1394]    [Pg.1394]    [Pg.1394]    [Pg.1395]    [Pg.1395]    [Pg.1395]    [Pg.656]    [Pg.658]    [Pg.7]    [Pg.407]    [Pg.381]    [Pg.383]    [Pg.391]    [Pg.392]    [Pg.392]    [Pg.393]   
See also in sourсe #XX -- [ Pg.606 ]

See also in sourсe #XX -- [ Pg.149 ]




SEARCH



Pascal

Pascal-second unit

© 2024 chempedia.info