Lithium reactions with alkenes

The reactive intermediates under some conditions may be the carbenoid a-haloalkyllithium compounds or carbene-lithium halide complexes.158 In the case of the trichloromethyllithium to dichlorocarbene conversion, the equilibrium lies heavily to the side of trichloromethyllithium at — 100°C.159 The addition reaction with alkenes seems to involve dichlorocarbene, however, since the pattern of reactivity toward different alkenes is identical to that observed for the free carbene in the gas phase.160... 

In addition to insertion into p-C—H bonds, cyclopropylidenes can undergo other reactions such as alkylation (c/. Section 4.7.3.2), dimerization, insertion into C—H bonds of the ether solvent (equation 60)183 or reaction with alkenes to afford spirocyclopropanes (equation 61).184 Addition of stoichiometric amounts of Bu OK has been shown to promote the reactions of lithium carbenoids, even at -83 C, with THF to give the insertion product (equation 62).185 Addition to alkenes is also promoted under these conditions. Intramolecular addition of the carbenoid to double bonds has been exploited in the synthesis of spirotricyclic compounds (equation 63).186... 

There is an alternative method for the preparation of organoborates which involves the reaction of triorganoborohydrides with alkenes or alkynes. The reaction with alkenes gives addition products (Eq. 5), whereas that with alkynes provides substitution products (Eq. 6). As 1-alkynyltrialkylborates are readily prepared by the reaction of trialkylboranes with lithium acetylides, the complexation reaction seems to be most convenient for producing tetracoordinate organoborates. 

Reactions of lithium alkyls are generally considered to be carbanionic in nature, but in reactions with alkyl halides free radicals have been detected by electron spin resonance.32 Lithium alkyls are widely employed as stereospecific catalysts for the polymerization of alkenes, notably isoprene, which gives up to 90% of 1,4-cA-polyisoprene numerous other reactions with alkenes have been studied.33 The TMED complexes again are especially active not only will they polymerize ethylene but they will even metallate benzene and aromatic compounds, as well as reacting with hydrogen at 1 atm to give LiH and alkane. 

A modified stepwise hydroboration avoiding the use of lithium aluminum hydride has also been developed (Schane 23.30). It was discovered that trialkylsilane reacts rapidly with boron trihalide to form unsolvated dihaloborane. Subsequent reaction with alkenes in the presence of sufficient boron trihalide occurs rapidly at -78°C to afford alkylboron dihalides without detectable contamination by dialkylboron halides. If additional equivalents of both trialkylsilane and alkene are added, dialkylboron halides are obtained. The methodology has been successfully applied to the synthesis of l,l,I-tris(dichloroboryl)alkanes, important precursors for dicarbapentaboranes. ... 

Seven procedures descnbe preparation of important synthesis intermediates A two-step procedure gives 2-(HYDROXYMETHYL)ALLYLTRIMETH-YLSILANE, a versatile bifunctional reagent As the acetate, it can be converted to a tnmethylenemethane-palladium complex (in situ) which undergoes [3 -(- 2] annulation reactions with electron-deficient alkenes A preparation of halide-free METHYLLITHIUM is included because the presence of lithium halide in the reagent sometimes complicates the analysis and use of methyllithium Commercial samples invariably contain a full molar equivalent of bromide or iodide AZLLENE IS a fundamental compound in organic chemistry, the preparation... 

PREPARATION OF ALKENES BY REACTION OF LITHIUM DIPROPENYLCUPRATES WITH ALKYL HALIDES ( )-2-UNDECENE... 

The mixed lithium aminophosphonium azadiylides 7 [47] are known to be involved in reaction with various electrophiles specifically at the carbon center. The reaction with carbonyl known to form betaine adducts was recently used for the first time in Wittig type reactions for the synthesis of di-, tri-, and tetrasubsti-tuted alkenes 8 [52]. 

Method G is used to introduce the alkyl fragment when less reactive alkenes are employed or for cases where functionality within the dienophilic alkene undergoes reaction with the Grignard reagent. Following this procedure, a lithium anion is first added to the aldehyde 5 at 78 °C.27 After consumption of the aldehyde has been determined by TLC, the dienophile is added and magnesium bromide is introduced. The cycloaddition occurs as the reaction warms to room temperature. In the case of... 

Related to the nitrile oxide cycloadditions presented in Scheme 6.206 are 1,3-dipolar cycloaddition reactions of nitrones with alkenes leading to isoxazolidines. The group of Comes-Franchini has described cycloadditions of (Z)-a-phenyl-N-methylnitrone with allylic fluorides leading to enantiopure fluorine-containing isoxazolidines, and ultimately to amino polyols (Scheme 6.207) [374]. The reactions were carried out under solvent-free conditions in the presence of 5 mol% of either scandium(III) or indium(III) triflate. In the racemic series, an optimized 74% yield of an exo/endo mixture of cycloadducts was obtained within 15 min at 100 °C. In the case of the enantiopure allyl fluoride, a similar product distribution was achieved after 25 min at 100 °C. Reduction of the isoxazolidine cycloadducts with lithium aluminum hydride provided fluorinated enantiopure polyols of pharmaceutical interest possessing four stereocenters. 

The conversion of the polystyrene-supported selenyl bromide 289 into the corresponding acid 290 allowed dicyclohexylcarbodiimide (DCC)-mediated coupling with an amidoxime to give the 1,2,4-oxadiazolyl-substituted selenium resin 291 (Scheme 48). Reaction with lithium diisopropylamide (LDA) and allylation gave the a-sub-stituted selenium resin 292, which was then used as an alkene substrate for 1,3-dipolar cycloaddition with nitrile oxides. Cleavage of heterocycles 293 from the resin was executed in an elegant manner via selenoxide syn-elimination from the resin <2005JC0726>. 

E Selective Wittig reagents. The reaction of 1 with lithium in THF provides LiDBP, which on reaction with an alkyl halide (2 equiv.) and NaNH2 in THF gives a salt-free ylide such as 2 or 3, formed by reaction with ethyl iodide or butyl iodide, respectively. These ylides react readily with aldehydes at —78°, but the intermediate oxaphosphetanes are unusually stable and require temperatures of 70-110° for conversion to the phosphine oxide and the alkene, which is obtained in E/Z ratios of 6-124 1. Highest (E)-selectivity is observed with a-branched aldehydes. 

---