Flow rate factors affecting

Another important factor affecting diffusion rate is the solubihty of the gas in blood. When the solnbihty of the gas in blood is large, the diffusion rate is fast and the gas is removed qnickly from the alveoli. In this case, the limiting factor in dehvery of gas to the blood is the rate of supply of gas to the alveoli. When this solnbihty is small, the diffnsion rate is slow thus blood flow (i.e., cardiac output) rather than minnte volume becomes the rate-limiting factor in toxicity. 

Positive displacement pumps deliver a definite volume of liquid for each cycle of pump operation. Therefore, the only factor that affects flow rate in an ideal positive displacement is the speed at which it operates. The flow resistance of the system in which the pump is operating will not affect the flow rate through the pump. Figure 21.18 shows the characteristic curve for a positive displacement pump. 

In general, among the important factors affecting evaporation rate of a solvent from a wet film are vapor pressure of the solvent, temperature, the air flow rate at the surface, and the wet film thickness. 

Scale-Up Principles. Key factors affecting scale-up of reactor performance are nature of reaction zones, specific reaction rates, and mass- and heat-transport rates to and from reaction sites. Where considerable uncertainties exist or large quantities of products are needed for market evaluations, intermediate-sized demonstration units between pilot and industrial plants are usehil. Matching overall fluid flow characteristics within the reactor might determine the operative criteria. Ideally, the smaller reactor acts as a volume segment of the larger one. Elow distributions are not markedly influenced by... 

Factors affecting RO membrane separations and water flux include feed variables such as solute concentration, temperature, pH, and pretreatment requirements membrane variables such as polymer type, module geometry, and module arrangement and process variables such as feed flow rate, operating time and pressure, and water recovery. 

The characteristics of WC, especially grain size, are determined by purity, particle shape and grain size of the starting material, and the conditions employed for reduction and carburization. The course of the reaction WO3 — W — WC is dependent on temperature, gas flow rates, water-vapor concentration in the gas, and the depth of the powder bed. All these factors affect the coarsening of the grain. 

The hydrauhc diameter method does not work well for laminar flow because the shape affects the flow resistance in a way that cannot be expressed as a function only of the ratio of cross-sectional area to wetted perimeter. For some shapes, the Navier-Stokes equations have been integrated to yield relations between flow rate and pressure drop. These relations may be expressed in terms of equivalent diameters Dg defined to make the relations reduce to the second form of the Hagen-Poiseulle equation, Eq. (6-36) that is, Dg (l2SQ[LL/ KAPy. Equivalent diameters are not the same as hydraulie diameters. Equivalent diameters yield the correct relation between flow rate and pressure drop when substituted into Eq. (6-36), but not Eq. (6-35) because V Q/(tiDe/4). Equivalent diameter Dg is not to be used in the friction factor and Reynolds number ... 

Determination of Controlling Rate Factor The most important physical variables determining the controlhng dispersion factor are particle size and structure, flow rate, fluid- and solid-phase diffu-sivities, partition ratio, and fluid viscosity. When multiple resistances and axial dispersion can potentially affect the rate, the spreading of a concentration wave in a fixed bed can be represented approximately... 

Variations in viscosity of both the incoming and finished products have a dramatic effect on mixer performance. Standard operating procedures should include specific operating guidelines for the range of variation that is acceptable for each application. The recommended range should include adjustments for temperature, flow rates, mixing speeds, and other factors that directly or indirectly affect viscosity. 

Quantitative analysis using the internal standard method. The height and area of chromatographic peaks are affected not only by the amount of sample but also by fluctuations of the carrier gas flow rate, the column and detector temperatures, etc., i.e. by variations of those factors which influence the sensitivity and response of the detector. The effect of such variations can be eliminated by use of the internal standard method in which a known amount of a reference substance is added to the sample to be analysed before injection into the column. The requirements for an effective internal standard (Section 4.5) may be summarised as follows ... 

Much LC-MS work is carried out in a qualitative or semi-quantitative mode. Development of quantitative LC-MS procedures for polymer/additive analysis is gaining attention. When accurate quantitation is necessary, it is important to understand in depth the experimental factors which influence the quantitative response of the entire LC-MS system. These factors, which include solvent composition, solvent flow-rate, and the presence of co-eluting species, exert a major influence on analyte mass transport and ionisation efficiency. Analyte responses in MS procedures can be significantly affected by the nature of the organic modifier used in the RPLC... 

---