Electrodes inactive

Besides the differential equations the complete formulation of the model requires a set of initial and boundary conditions. These must reflect the situation at the interface between measuring solution and enzyme electrode membrane and between membrane and sensor. For the models considered, it is assumed that the measuring solution is perfectly mixed and contains a large amount of substrate as compared to the substrate converted in the enzyme membrane. It has been shown experimentally (Carr and Bowers, 1980) that in measuring solutions diffusion is much more rapid than in membranes. A boundary layer effect is not considered. On the sensor side all electrode-inactive substances fulfill zero flux conditions. If the model contains more than one layer the transfer between the layers may be modeled by using relations of mass conservation. The respective equations will be given in the following sections. 

Accordingly, the modeling of the dynamic behaviour of an electrode-inactive substance in a monoenzyme layer and with a reaction rate linear with respect to S is as follows ... 

Ion implantation has also been used for the creation of novel catalyticaHy active materials. Ruthenium oxide is used as an electrode for chlorine production because of its superior corrosion resistance. Platinum was implanted in mthenium oxide and the performance of the catalyst tested with respect to the oxidation of formic acid and methanol (fuel ceU reactions) (131). The implantation of platinum produced of which a catalyticaHy active electrode, the performance of which is superior to both pure and smooth platinum. It also has good long-term stabiHty. The most interesting finding, however, is the complete inactivity of the electrode for the methanol oxidation. 

Multienzyme Electrodes. Coupling the reactions of two or more immobilized enzymes increases the number of analytes that can be measured. An electro-inactive component can be converted by an enzyme to a substrate that is subsequentiy converted by a second enzyme to form a detectable end product (57). For example, a maltose [69-79-4] sensor uses the enzymes glucoamylase and glucose oxidase, which convert... 

For an electrochemical cell consisting of a metal at the potential of zero charge in a solution of surface-inactive electrolyte and a reference electrode (let us assume that any liquid junction potential can be neglected), the electrode potential is given by (cf. Eq. (20)]... 

The electrical double-layer structure at Ga/DMF, In(Ga)/DMF, and Tl(Ga)/DMF interfaces upon the addition of various amounts of NaC104 as a surface-inactive electrolyte has been investigated by differential capacitance, as well as by the streaming electrode method.358 The capacitance of all the systems was found to be independent of the ac frequency, v. The potential of the diffuse layer minimum was independent of... 

Cu crystallizes in the fee and its melting point is 1356 K. The experimental data for single-crystal Cu/H20 interfaces are also controversial. 567 570,572 57X The first studies with Cu(l 11), Cu(100), and Cu(l 10) in surface-inactive electrolyte solutions (NaF, Na2S04) show a capacitance minimum at E less negative than the positive limit of ideal polarizability of Cu electrodes (Table 11). depends on the method of surface... 

The electrical double layer at pc-Zn/fyO interfaces has been studied in many works,154 190 613-629 but the situation is somewhat ambiguous and complex. The polycrystalline Zn electrode was found to be ideally polarizable for sufficiently wide negative polarizations.622"627 With pc-Zn/H20, the value of Eg was found at -1.15 V (SCE)615 628 (Table 14). The values of nun are in reasonable agreement with the data of Caswell et al.623,624 Practically the same value of Eff was obtained by the scrape method in NaC104 + HjO solution (pH = 7.0).190 Later it was shown154,259,625,628 that the determination of Eo=0 by direct observation of Emin on C,E curves in dilute surface-inactive electrolyte solutions is not possible in the case of Zn because Zn belongs to the group of metals for which E -o is close to the reversible standard potential in aqueous solution. 

Vitanov and Popov et al.156 660-662 have studied Cd(0001) electrolyti-cally grown in a Teflon capillary in an aqueous surface-inactive electrolyte solution. The E is independent of ce) and v. The capacity dispersion is less than 5%, and the electrode resistance dispersion is less than 3%. The adsorption of halides increases in the order Cl" < Br" < I".661 A comparison with other electrodes shows an increase in adsorption in the sequence Cd(0001) < pc-Cd < Ag( 100) < Ag(l 11). A linear Parsons-Zobel plot with /pz = 1.09 has been found at a = 0. A slight dependence has been found for the Cit a curves on ce, ( 5%) in the entire region of a. Theoretical C, E curves have been calculated according to the GCSG model. 

First attempts to study the electrical double layer at A1 electrodes in aqueous and nonaqueous solutions were made in 1962-1965,182,747,748 but the results were not successful.190 The electrical double-layer structure at a renewed Al/nonaqueous solution of surface-inactive electrolytes such as (CH3)4NBF4) (CH3)4NC104, (CH3>4NPF6, and (C4H9)4NBF4, has been investigated by impedance.749-751 y-butyrolactone (y-BL), DMSO, and DMF have been used as solvents. In a wide region of E [-2.5 [Pg.128]

The first studies of the electrical double-layer structure at Sn + Pb and Sn + Cd solid drop electrodes in aqueous surface-inactive electrolyte solutions were carried out by Kukk and Piittsepp.808 Alloys with various contents of Pb (from 0.2 to 98%) were investigated by impedance.615,643,667,816 Small amounts of Pb caused dramatic shifts of toward more negative values. For alloys with Pb bulk content 0.2%, was the same as for pc-Pb. The was independent of Crf and frequency. C xt Cjl plots were linear, with/pz very close to unity. Thus the surface of Sn + Pb alloys behaves as if it were geometrically smooth, and Pb appears to be the surface-active component. 

In Table 25 the values of E Lo - in molten salt (eutectic LiCl + KC1 melt) are compared with AE in aqueous solutions (relative to the value of Eo=0 for a pc-Pb electrode in a surface-inactive aqueous electrolyte). According to these data, the difference of AEaf in aqueous electrolytes and molten salts is not very high to a first approximation, it can be assumed that the quantity in square brackets in Eq. (61) has the greatest... 

Unlike the cathodic reaction, anodic oxidation (ionization) of molecular hydrogen can be studied for only a few electrode materials, which include the platinum group metals, tungsten carbide, and in alkaline solutions nickel. Other metals either are not sufficiently stable in the appropriate range of potentials or prove to be inactive toward this reaction. For the materials mentioned, it can be realized only over a relatively narrow range of potentials. Adsorbed or phase oxide layers interfering with the reaction form on the surface at positive potentials. Hence, as the polarization is raised, the anodic current will first increase, then decrease (i.e., the electrode becomes passive see Fig. 16.3 in Chapter 16). In the case of nickel and tungsten... 

The second pathway is seen distinctly at mercury and graphite electrodes. These electrodes are quite inactive in the catalytic decomposition of H2O2. Moreover, at them the potential where the peroxide is reduced further is more negative than the potential where it is formed from oxygen. Hence, within a certain range of not too negative potentials, the reaction can occur in such a way that the hydrogen peroxide formed accumulates in the solution. 

In some cases, adsorbed foreign species may give rise to acceleration of a reaction. In the hterature, a few cases have been described where strong catalytic effects were observed on catalytically inactive electrodes when small amounts of platinum species that had by accident arrived in the electrolyte solution became adsorbed on their surface. 

The charge density on the electrode a(m) is mostly found from Eq. (4.2.24) or (4.2.26) or measured directly (see Section 4.4). The differential capacity of the compact layer Cc can be calculated from Eq. (4.3.1) for known values of C and Cd. It follows from experiments that the quantity Cc for surface inactive electrolytes is a function of the potential applied to the electrode, but is not a function of the concentration of the electrolyte. Thus, if the value of Cc is known for a single concentration, it can be used to calculate the total differential capacity C at an arbitrary concentration of the surface-inactive electrolyte and the calculated values can be compared with experiment. This comparison is a test of the validity of the diffuse layer theory. Figure 4.5 provides examples of theoretical and experimental capacity curves for the non-adsorbing electrolyte NaF. Even at a concentration of 0.916 mol dm-3, the Cd value is not sufficient to permit us to set C Cc. 

Fig. 4.7 Schematic dependence of the quantities y, y°, o °o, Ce — C and T on the electrode potential. The quantities with the superscript 0 refer to a surface-inactive electrolyte while those without a superscript refer...

The inhibition of electrode processes as a result of the adsorption of electroinactive surfactants has been studied in detail at catalytically inactive mercury electrodes. In contrast to solid metal electrodes where knowledge of the structure of the electrical double layer is small, it is often possible to determine whether the effect of adsorption on the electrode process at mercury electrodes is solely due to electrostatics (a change in potential 02)... 

The first catalysts reported for the electroreduction of C02 were metallophthalocyanines (M-Pc).126 In aqueous solutions of tetraalkylammonium salts, current-potential curves at a cobalt phthalocyanine (Co-Pc)-coated graphite electrode showed a reduction current peak whose height was proportional to the C02 concentration and to the square root of the potential sweep rate at a given C02 concentration. On electrolysis, oxalic acid and glycolic acid were detected, but formic acid was not. Mn and Pd phthalocyanines were inactive, while Cu and Fe phthalocyanines were slightly active. At the potentials used for C02 reduction, M-Pc catalysts would be in their dinegative state, and the occupied dz2 orbital of the metal ion in the metallophthalocyanine was suggested to play an important role in the catalytic activity. 

---