Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Declared values

This is to be determined at rated voltage and frequency and can be carried out between 0.9 to I. I times the rated voltage and 0.8 to 1.2 times the rated frequency. Permissible tolerances in capacitance from the declared values can be as follows ... [Pg.838]

The test can be performed at voltages and frequencies, as noted in (1) above. The value of tan 5 should not exceed the declared value. [Pg.839]

If a trend is to be described by an ordered sequence of maximal episodes, then we only need to generate a language that contains the declarative value of an episode. Such a language was proposed by Cheung and Stephanopoulos (1990). It is composed of seven primitives (Fig. 4a) and possesses the following properties ... [Pg.220]

The Declared Values. These values should be the average values as defined above and should be derived from ... [Pg.49]

Fig. 4.3. Typical graph for correcting measured sample dry matter digestibility (DMD) values in proportion to deviation of low and high standards from their declared values. Fig. 4.3. Typical graph for correcting measured sample dry matter digestibility (DMD) values in proportion to deviation of low and high standards from their declared values.
It Is worthy of remark, that in tlio year 1844, the year before the excise duties wore repealed, and with all the advantage of a drawback, the total exports of glass, of British manufacture, were only of the declared value of twenty-six thousand six hundred and ninety-four pounds 5 whereas, It will be seen from the preceding table, that in 1855, or ten years after the repeal of the duties, they amounted in value to upwards of half a million sterling. [Pg.250]

Assaying of Tin Okes.—Although the laws of the Stannery Court do not permit that the product of the tin mines should be sold out of Cornwall before smelting, it happens that the mining proprietors are never the smelters, and so the ores are sold to a few smelters who have the trade in their hands. These buy as cheaply as they oan, and according to the declared value of tho oro as ascertained by assay. Hance, as in the case of copper, the ores of tin are always submitted to... [Pg.1061]

Given the information above and that the cereal needs to have a vitamin level above the declared value of 6500 lU for 1 year at 25°C, what lU should be present in the cereal at the time it is manufactured Your answer may also be reported in percent overuse (Aiu. 12%)... [Pg.400]

At what percent of declared value of 6500 lU must you apply the vitamin If 10,000,000 Ib/yr of the cereal is made and the nutrient cost is 5 per pound, how much will this overuse cost ... [Pg.400]

Compliance with a declared value may be proved via an authority-authorised measurement programme [9]. [Pg.293]

It is known that in the early 1950 s many samples of what germ oil were available in which chemical analysis by the methods available at that time showed the actual content of tocopherol to be considerably less than the declared value. In the paper there is no reference to a check analysis having been made on the capsules either before, during, or after the termination of the experiment. [Pg.581]

The initials NR and DV used in Tables 3.13 and 3.14 are abbreviations of the following NR for no requirement (this class has been included for countries where the characteristic property is not subject to regulatory requirements) and DV for declared value , which means that the manufacturer is required to provide a value or value range for the product. [Pg.120]

The recommended limiting values set for all the above parameters are as shown in Table 7.10. The above parameters/criteria are used at the mix design stage for the determination of the target mix or for the evaluation of its conformity to the declared value by the producer. [Pg.377]

Note SDV = supplier-declared value grading range (S) lblerance = permitted tolerance, from supplier-declared value. [Pg.466]

In view of these problems, it is recommended that the declared value should be doubled when comparisons are made with exposure limits. [Pg.310]

The tolerance band indicates the maximum tolerance variation in the declared value of resistance. Thus a 1000 resistor with a 5% tolerance will have a value somewhere between 95 and 1050, since 5% of 100 O is 50. [Pg.166]


See other pages where Declared values is mentioned: [Pg.121]    [Pg.249]    [Pg.449]    [Pg.562]    [Pg.207]    [Pg.18]    [Pg.470]    [Pg.364]    [Pg.245]    [Pg.465]    [Pg.24]    [Pg.721]    [Pg.263]    [Pg.417]    [Pg.103]    [Pg.1388]   
See also in sourсe #XX -- [ Pg.49 ]




SEARCH



Declaration

© 2024 chempedia.info