Conducting agents

Haas, H. L. (1984). Histamine potentiates neuronal excitation by blocking a calcium-dependent potassium conductance. Agents Actions 14, 534-7. 

Characteristics can be adapted by optimization of the formulations heat or light stabilizers, fire retardants, conductive agents... 

It is in itself the motor [le moteurj the limbs are its conducting agents it particularly expends itself in the fingers and in the brain. There exists... 

Another approach to monolithic imprinted polymer capillary columns has been reported. The polymerisation was performed at 60°C and thus thermally initiated [70,71]. The result is a dense polymer inside the whole capillary. The resulting MIP capillary then has to be connected to an electrolyte-filled open capillary via a teflon tube and a detection window is prepared on the open capillary to facilitate detection (as described above. Fig. 16.2). Also, ammonium acetate (1-2 mM) is added as a conducting agent to the pre-polymerisation mixture. This is done to allow exchange of the solvent of polymerisation for electrolyte, which can be achieved electrophoretically by stepwise increase of the electric field until a stable base-line is obtained. 

Polyacetylene 1,622 as conducting agent 622 Polybutadiene binders see Binders in composite propellants Polybutadiene binders with carboxylic function 602.60S... 

Poly( 1,2 oxypropylene)diol f PPG) 604 Po(y-p-phenylene arsenic penufluoride, as conducting agent 622 Polyurethane binders 602.603.605... 

The fillers are added so that the adhesives are sag-free, motionless and form shapes that suit the components to be bonded, reduce shrinkage during cure, increase thermal conductivity, improve corrosion resistance and reduce costs. The concentration of these curatives, fillers and conducting agents is usually monitored using ICP-OES. 

Uses Conductivity agent for electrostatically sprayed coatings, solv.-based air-dry and baking enamels... 

Uses Conductivity agent, antistat for electrostatic spray paints Features Not suitable for wh. painfs which will be stoved or put onto hot surfs., such as radiafors yellowing may occur Properties Flash pf. (PMCC) 40 C cafionic 80% act. in n-butanol Use Level 0.5-3% (paint)... 

Chem. Descrip. Coco-ethyidimonium ethosultate in ethylene glycol Uses Conductivity agent, antistat for plastics, electrostatic spray paints. Inks, adhesives... 

Uses Conductivity agent in acrylic-based systems for conductive coatings for ESD and ESP... 

Chem. Descrip. Haiogen-free compound in n-butanoi Uses Conductivity agent for coatings, eiectrostatic sprayed paints Properties Lt. amber ciear iiq. dens. 0.94-0.96 g/cm (20 C) tiash pt. 36 C cationic 78-82% act. 

Uses Conductivity agent for extrusions and coatings, suitable for flooring and surfs, where high m.w. resins are used Features Rec. where decorative ettects and ESD control are required Properties Off-wh. flake resist. 10 ° ohm Elektrostat 100/50 [Magnesium Elektron]... 

Conductive Dispersion 1000 Series Conductive Dispersion 3000 Series conductivity agent, acrylic-based systems ESP conductive coatings Conductive Dispersion 1000 Series Conductive Dispersion 3000 Series conductivity agent, coalings EFKA -6780 EFKA -6782 ElekVoslat 80/ 54 Elekiroslal 100/50 conductivity agent, electrostatic spray... 

Catafor CA 80 Catafor F conductivity agent, eiectrostatic sprayed paints... 

EFKA -6780 EFKA -6782 conductivity agent, etectrostaticaiiy sprayed coatings... 

In the electrode fabrication process, the active materials are coated onto metal foils and calendered. The positive electrode consists of active material, such as LiCoOj, LiNiOj, or Li MnO a carbon-conductive agent such as acetylene black, Ketjen... 

The positive electrode is produced as follows the LiCo02 powder of the positive active material and carhon black conducting agent are mixed with an N-methyl pyrrolidone (NMP) solution of PVDF binder to make a paste of appropriate viscosity. A mixture of water and carboxyl methylcellulose (CMC), with styrene butadiene rubber (SBR, used as a binding agent), is also used for making such paste. 

Carbon aUotropes as the conductive agent such as for carbon fibers, or when in the synthetic polymeric filament production step conductive particles such as carbon black, graphite, graphene, or carbon nanotubes are used. 

Conductive polymer such as poly aniline (PANI), polypyrrole (PPy), poly (3,4-ethylenediox-)rthiophene) (PEDOT) as the conductive agent, most often blended with a common fiber forming polymer (PA, PES, etc.) in the extrasion. 

---