Carbodiimides 1-oxides

Carbodiimide formation is markedly accelerated when phosphine oxides (R PO) or phosphates are used as catalysts. Intermediates with P—NR bonds have been postulated as iatermediates ia these reactioas (59,60). 

Garbodiimide Formation. Carbodiimide formation has commercial significance in the manufacture of Hquid MDI. Heating of MDI in the presence of catalytic amounts of phosphine oxides or alkyl phosphates leads to partial conversion of isocyanate into carbodiimide (95). The carbodiimide (39) species reacts with excess isocyanate to form a 2 + 2cycloaddition product. The presence of this product in MDI leads to a melting point depression and thus a mixture which is Hquid at room temperature. 

Other Reactions. 2-Dioxolaniniines, 2-oxathiolaniniines, and 2-oxa2o1idinimines result from the reaction of propylene oxide with isocyanates, isothiocyanates, and carbodiimides, respectively (103,104). 

In a manner analogous to classic nitrile iinines, the additions of trifluoro-methylacetonitrile phenylimine occur regiospecifically with activated terminal alkenes but less selectively with alkynes [39], The nitnle imine reacts with both dimethyl fumarate and dimethyl maleate m moderate yields to give exclusively the trans product, presumably via epimenzation of the labile H at position 4 [40] (equation 42) The nitrile imine exhibits exo selectivities in its reactions with norbornene and norbornadiene, which are similar to those seen for the nitrile oxide [37], and even greater reactivity with enolates than that of the nitnle oxide [38, 41], Reactions of trifluoroacetomtrile phenyl imine with isocyanates, isothiocyanates, and carbodiimides are also reported [42]... 

The facile and selective oxidation of both primary and secondary hydroxy groups with certain nucleotides led Pfitzner and Moffatt (48) to explore the scope of the carbodiimide-methyl sulfoxide reagent with steroid and alkaloid alcohols. Relatively minor differences were apparent in the rate of oxidation of epimeric pairs of 3- and 17- hydroxy steroids whereas the equatorial lLx-hydroxyl group in several steroids was readily oxidized under conditions where the axial epimer was unreactive [cf. chromic oxide oxidation (51)]. 

Roughly 0.6-0.8 g. of the urea is usually obtained, m.p. 232-234°. The excess dicyclohexylcarbodiimide remains in the benzene. The oxidation is generally less satisfactory if less than 2.5 molar equivalents of carbodiimide is used. 

POLYMERIC CARBODIIMIDE. II. MOFFAT OXIDATION 4-tert-BUTYLCYCLOHEXANONE... 

Carbodiimides have been prepared by desulfurization of thioureas by metal oxides, by sodium hypochlorite,4 or by ethyl chloroformate in the presence of a tertiary amine by halogena-tion of ureas or thioureas followed by dehydrohalogenation of the N,N -disubstituted carbamic chloride 8 and by dehydration of disubstituted ureas using -toluenesulfonyl chloride and pyridine.7 The method described above is a modification of that of Campbell and Verbanc. ... 

Poly (ethylene oxide) macromonomers72 761 are made in a similar way, as the alkoxide end group is reactive enough towards benzylic halides. With methacryloyl chloride, side reactions are involved. It is better to first protonate the PEO, and then to have it react with methacryloyl chloride in the presence of some triethyl amine. One can also react co-hydroxy polyethylene oxide) with methacryloyl imidazole, or with methacrylic acid in the presence of dicyclohexyl carbodiimide (DCCf)77). 

The treatment of isocyanates with 3-methyl-l-ethyl-3-phosphoIene-l-oxide (59) is a useful method for the synthesis of carbodiimides in good yields. The mechanism does not simply involve the addition of one molecule of isocyanate to another, since the kinetics are first order in isocyanate and first order in catalyst. The following mechanism has been proposed (the catalyst is here represented as... 

High modulus blends can be developed by mixing TPU with acetal copolymer (trioxane ethylene oxide copolymers) [242-244]. The highly crystalline acetal forms a second continuous phase. Kumar et al. studied behavior of such blends [245]. TPU retains none of its physical properties after immersion in water at 70°C for three weeks. The hydrolysis resistance of TPU can be improved by blending with polycarbodiimides [246]. Two parts of carbodiimide with TPU offer 87% retention of its strength, 93% of elongation, and 75% of modulus under the same... 

Such carbonyls may be further oxidized using potassium permanganate (KMnO and perchloric acid (HCIO4) to convert all of these groups into carboxylic acids. Once functionalized in this manner, the nanotubes can be fully dispersed in aqueous systems. Kordas et al. (2006) used these derivatives to print nanotube patterns on paper or polymer surfaces to create conductive patterns for potential use in electronic circuitry. The carboxylates also may be used as conjugation sites to link other ligands or proteins to the nanotube surface using a carbodiimide reaction as previously discussed (Section 1, this chapter Chapter 2, Section 1.11 Chapter 3, Section 1). 

The ethylene diamine-dextran derivative may be used for the coupling of carboxylate-contain-ing molecules by the carbodiimide reaction, for the coupling of amine-reactive probes, or to modify further using heterobifunctional crosslinkers. The hydrazide-dextran derivative may be used to crosslink aldehyde-containing molecules, such as oxidized carbohydrates or glycoproteins. 

Hydrazide groups can react with carbonyl groups to form stable hydrazone linkages. Derivatives of proteins formed from the reaction of their carboxylate side chains with adipic acid dihydrazide (Chapter 4, Section 8.1) and the water-soluble carbodiimide EDC (Chapter 3, Section 1.1) create activated proteins that can covalently bind to formyl residues. Hydrazide-modified enzymes prepared in this manner can bind specifically to aldehyde groups formed by mild periodate oxidation of carbohydrates (Chapter 1, Section 4.4). These reagents can be used in assay systems to detect or measure glycoproteins in cells, tissue sections, or blots (Gershoni et al., 1985). 

The aldehyde 38 was obtained from 35, by way of 36 and 37, by the carbodiimide—dimethyl sulfoxide oxidation procedure52 in the presence of 3-(3-dimethylaminopropyl)-l-ethylcarbodiimide hydrochloride (EDAC)53 and dichloroacetic acid. It was isolated in the form of its crystalline 1,3-diphenylimidazolidine derivative (39) by trapping the freshly prepared aldehyde 38 with N,N -diphen-ylethylenediamine. (This reagent was developed by Wanzlick and Lochel54 for the selective derivatization of aldehydes, and has been exploited for the isolation of nucleoside 5 -aldehydes55 and other aldehydo derivatives of carbohydrates by Moffatt and coworkers.52(b))... 

---