Argon oxide

The action of oxygen is rather anomalous, as it can act as an initiator but also as an inhibitor. For this reason, the medium of polymerisation is usually degassed and polymerisation performed under an inert atmosphere, e.g. nitrogen or ideally argon. Oxidants such as FeCls and CuCl2 are strong inhibitors. 

Molecular area, a ,(Ar), of argon at 77 K on nonporous oxides (Argon BET plots constructed withp (liquid) BET surface areas calculated from nitrogen isotherms, with a (Na) = 16-2 A )... 

As already mentioned, the choice of the supercooled liquid as reference state has been questioned by some workers who use the saturation vapour pressure of the solid, which is measured at the working temperature in the course of the isotherm determination. The effect of this alternative choice of p° on the value of a for argon adsorbed on a number of oxide samples, covering a wide range of surface areas, is clear from Table 2.11 the average value of is seen to be somewhat higher, i.e. 18 OA. ... 

In view of the widespread use of nitrogen and argon in surface area and porosity studies, data for the construction of the standard a,-curves for these adsorbates on hydroxylated silica, are given in Table 2.14 (p. 93) for nitrogen and in Table 2.15 for argon. From the arguments of Section 2.12, these should be adequate for other oxides such as alumina, if high accuracy is not called for. 

Calculations of the interaction energy in very fine pores are based on one or other of the standard expressions for the pair-wise interaction between atoms, already dealt with in Chapter 1. Anderson and Horlock, for example, used the Kirkwood-Miiller formulation in their calculations for argon adsorbed in slit-shaped pores of active magnesium oxide. They found that maximum enhancement of potential occurred in a pore of width 4-4 A, where its numerical value was 3-2kcalmol , as compared with 1-12, 1-0 and 1-07 kcal mol for positions over a cation, an anion and the centre of a lattice ceil, respectively, on a freely exposed (100) surface of magnesium oxide. 

Polymers. Ion implantation of polymers has resulted in substantial increases of electrical conductivity (140), surface hardness (141), and surface texturing (142). A four to five order of magnitude increase in the conductivity of polymers after implantation with 2 MeV Ar ions at dose levels ranging from 10 -10 ions/cm has been observed (140). The hardness of polycarbonate was increased to that of steel (141) when using 1 MeV Ar at dose levels between 10 -10 ions/cm. Conductivity, oxidation, and chemical resistance were also improved. Improvements in the adhesion of metallizations to Kapton and Teflon after implantation with argon has been noted (142). 

In a vacuum, uncoated molybdenum metal has an unlimited life at high temperatures. This is also tme under the vacuum-like conditions of outer space. Pure hydrogen, argon, and hehum atmospheres are completely inert to molybdenum at all temperatures, whereas water vapor, sulfur dioxide, and nitrous and nitric oxides have an oxidizing action at elevated temperatures. Molybdenum is relatively inert to carbon dioxide, ammonia, and nitrogen atmospheres up to about 1100°C a superficial nitride film may be formed at higher temperatures in the latter two gases. Hydrocarbons and carbon monoxide may carburize molybdenum at temperatures above 1100°C. 

Synthesis Gas Preparation Processes. Synthesis gas for ammonia production consists of hydrogen and nitrogen in about a three to one mole ratio, residual methane, argon introduced with the process air, and traces of carbon oxides. There are several processes available for synthesis gas generation and each is characterized by the specific feedstock used. A typical synthesis gas composition by volume is hydrogen, 73.65% nitrogen, 24.55% methane, <1 ppm-0.8% argon, 100 ppm—0.34% carbon oxides, 2—10 ppm and water vapor, 0.1 ppm. 

---