Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About
0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | a | b | c | d | e | f | g | h | i | j | k | l | m | n | o | p | q | r | s | t | u | v | w | x | y | z

   |<      <<      >>     > |    


IV Formal Group Simulation Parameters HeIfand Model Using the Weber-

IV Formation of C5 Components in Beans

IV Frequency of Amino Acid Residues at Positions 32, 33, 34, and 35 of Heavy Chains 1

IV further Illustrates the effect of weight per urethane linkage, as well as that of oligomer molecular weight. If molecular weight and weight per urethane linkage are Increased by choice of polyol, without changing the stoichiometry, a decrease in viscosity is observed . In this case, the effect of urethane content dominates.

IV Gasoline Stocks Analyses

IV General Biological Properties and Methods of Steriluation of Antibacterial

IV gives a few examples of terpenes shown to be Insect deterrents. As with the previous examples of Insect attractants In Tables II and III, the structural diversity of the deterrent compounds Is remarkable. There are no clear and logical structure-activity relationships among the compounds with these behavioral effects. Specialised and unique effects and behavioral adaptations are thus the rule In Interactions between species rather than the exception.

IV gives a list of natural sialic acids and derivatives prepared with sialyl aldolase. Some properties of natural sialic acids have been reviewed37 in a Volume of this Series.

IV gives a summary of the packed beds that we made use of in this section. The term Cm reflects the two-dimensional effects for Rem 0. A value of zero, for 100 the experimental data.

IV gives actual and estimated production costs for a number of conditions. Costs cannot be directly compared, as they are affected by plant output and the degree of desalting. In this particular case they can, however, be compared more nearly if calculated per 1000 gallons and per 1000 p.p.m. TDS removed.

IV gives all of the values obtained for mercury in coal, which range from 0.057 to 0.198 ppm with most values in the range of 0.07 ppm. Our attempt at a mercury balance for runs 5 and 9 is shown in Table V. From these numbers it is clear that very little mercury , except that these authors were able to collect the mercury in the gas phase. Their data shows that most of the mercury is in the gas phase. This can also be implied from our results.

IV gives an example of our own work on the polymerization of a number of higher aldehydes. Potassium triphenylmethoxide—a soluble initiator—polymerized a number of higher aldehydes to crystalline isotactic poly aldehydes. Table V lists a number of alkali alkoxides and other related compounds used as initiators for the n-butyraldehyde polymerization. Neither the type of the alkoxide nor the cation is of any great importance for the polymerization rate, the polymer yield, and stereoregularity of the resulting polyaldehyde as long as the initiator is adequately soluble in the reaction mixture.

IV gives illustrations of these situations. It is very unlikely that any producer would lack the resources to conduct the necessary trials and realize the consequent improvements if scale-up went well.

IV gives minimum steam requirement .

IV gives our procedure for the preparation of spray dried propargite.

IV gives results for the two types of test and several choices of element patterns. Important dual pattern Identification conclusions follow

IV gives some examples of possible strategies to test the few-hits-and-run model.

IV gives some of the parameters that have been derived from the manipulation of the integrated intensities of the various chemically shifted signals of the aromatic fractions and subfractions of Kuwait and South Louisiana crudes. Profiles that emerge from these baseline studies are the following

IV gives some results after applying the criteria for different tube diameters and operating conditions, as given in .

IV gives the analytical results obtained for all of the amino acids except cystine, cysteic acid, and tryptophan for the various irradiation treatments given in Table I as well as for the frozen nonirradiated control beef. Table V gives the assay data for cystine plus cysteine, by the colorimetric procedure, and cysteic acid. The assay data for tryptophan in Table V were determined by the fluorometric procedure.

IV gives the Attrition Indexes for the commercial and experimental samples. These values are reported for microspheres that were spray dried before the viscosity of the slurry exceeded 100 cP. The data show, again, that sol age and particle size of the CP alumina affect attrition. Sol age also seems to reduce the influence of the CP-2 as a binder. The Reference . The important point here is that the alumina particles can be incorporated into a standard FCC formula to change catalytic activity without a detrimental effect on attrition resistance.

IV gives the average physical property values of the three-layer bark extract bonded particleboards, involving each of the four coniferous bark extracts. The results reported are the averages of 9 boards, varying in density from 0.68-0.76 for each bark extract bonded particleboard. The properties of all boards meet medium density particleboard specifications in bending .

IV gives the composition of the Precambrian ocean after neutralization of HCl, calculated under these assumptions. The pH values correspond to the end of congruent solution of the original rocks of the Earth s crust and beginning of deposition of the carbonate and silicate facies of the BIF are consistent with the values of co, in the atmosphere. Questions of the proportion of the masses of CO2 m the atmosphere, hydrosphere, and carbonate sediments will be considered in more detail later.

IV gives the data from seven plots of Winesap and Rome Beauty apples in the Mississippi Valley. The spray schedules are similar to those used for the plots included in Table III, except that an additional parathion spray was applied on plots 9, 11, 14, and 4 on August 19, and the final harvest sample was taken on October 5. Only on the plot that was sprayed seven times with the 8-ounce strength of parathion did the spray residue at harvest approximate 0.1 p.p.m.

IV gives the essential parameters which were involved in successful biaxial orientation of this copolymer sample. The most im-



   |<      <<      >>     > |    

SEARCH



© 2024 chempedia.info