Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Slit geometry

Figure 2. Spectral photometric variation versus source position (1-3/im and 3-5/rm ranges). Upper surfaces are only affected by the geometrical effect of the slit geometry, and lower surfaces include the diffraction effects. Figure 2. Spectral photometric variation versus source position (1-3/im and 3-5/rm ranges). Upper surfaces are only affected by the geometrical effect of the slit geometry, and lower surfaces include the diffraction effects.
Flow in a Slit. Turning to a slit geometry, a flat velocity profile gives the simplest possible solution using Euler s method. The stability limit is independent of y ... [Pg.288]

A first necessary condition for the existence of the ID analog of Eq. (25) is the existence of a self-similar (asymptotic) velocity profile (itself equivalent to the existence of a ID equation for the flow field). This self-similar profile depends only on the wall Reynolds (Rew) number and has the following form (planar slit geometry) ... [Pg.252]

The above self-similar velocity profiles exists only for a Re number smaller than a critical value (e.g. 4.6 for a circular pipe). The self-similar velocity profiles must be found from the solution of the Navier-Stokes equations. Then they have to be substituted in Eq. (25) which must be solved to compute the local Nusselt number Nu z). The asymptotic Nusselt number 7Vm is for a pipe flow and constant temperature boundary condition is given by Kinney (1968) as a function of Rew and Prandtl (Pr) numbers. The complete Nu(z) curve for the pipe and slit geometries and constant temperature or constant flux boundary conditions were given by Raithby (1971). This author gave /Vm is as a function of Rew and fluid thermal Peclet (PeT) number. Both authors solved Eq. (25) via an eigenfunction expansion. [Pg.252]

The heat balance for the slit geometry in terms of gas mixing-cup temperature... [Pg.252]

As has already been pointed out in Sections 1.3 and 1.5, the slit-geometry is interesting for two reasons. First, it enables the measurement of flow birefringence in the 1—3 plane. Second, it furnishes the possibility to investigate polymer melts at high shear rates, where the cone-and-plate geometry fails. In the present section it remains to give a short description of the apparatus. [Pg.310]

These jumps follow from the Onsager relations. Unlike the 2-slit geometry, the closed ABI requires many reflections of the electron waves from the forks connecting the ring with the leads. Each such reflection adds a term to the interference sum of amplitudes, and modifies the simple 2-slit formula. In fact, unitarity (conservation of current) and time reversal symmetry imply that = Q 4>) [11], and therefore (3 (as well as 7 etc.) must be equal to 0 or 7T. The additional reflections also explain the need for higher harmonics near resonances. Below we include these many reflections, and replace the 2-slit formula by a new one - which can be used to extract olqd from the closed interferometer data [12]. [Pg.7]

Fig. 4. The CO-N2 doublet at mass 28 measured with the Chalk River ISOL and a FEBIAD ion source the resolving power is 20,000. With a slit-geometry source 16,000 has been obtained. (The separation between the two peaks is 10.5 MeV.)... Fig. 4. The CO-N2 doublet at mass 28 measured with the Chalk River ISOL and a FEBIAD ion source the resolving power is 20,000. With a slit-geometry source 16,000 has been obtained. (The separation between the two peaks is 10.5 MeV.)...
A. J. Poslinski and D. J. Coyle, Steady Gas Penetration through Non-Newtonian Liquids in Tube and Slit Geometries Isothermal Shear-Thinning Effects, Proc. Polymer Processing Society, 10th Annu. Meet., Akron, Ohio (1994), pp. 219-220. [Pg.819]

Lanthanum laurates were prepared as in Ref. [2]. The spectra of the angular correlation of annihilation photons (ACAP) were measured in a standard long-slit geometry using 22Na radioactive isotope as a positron source. [Pg.753]

Although many nitrogen molecules are adsorbed in pores that have slit shape (see Figure 6), most of them are in pores with shapes that significantly differ from a slit geometry. It is interesting to note that a significant fraction of the pores are quasi-one-dimensional, and the... [Pg.24]

An experimental trial for finding foe freezing point elevation phenomena was conducted, employing foe so-called colloidal-probe Atomic Force Microscopy. A carbonaceous nanospace with slit geometry was successfully made up by this technique. [Pg.238]

Of course, given a molecule in the pore volume, its total gas-solid interaction with the pore, Ugs, must be calculated by summing up its interaction energy with the three pore walls The rest of the simulation procedure is the same as for the case of slit geometry. [Pg.394]

Figure 1. N2 adsorption isotherms for series D (a) and series H (b) carbons lines are experimental data, symbols are MC calculations with slit geometry. (O) D8 and H8, (A) D19 and H22, ( ), D52 and H52, (0) D70 and H74. Figure 1. N2 adsorption isotherms for series D (a) and series H (b) carbons lines are experimental data, symbols are MC calculations with slit geometry. (O) D8 and H8, (A) D19 and H22, ( ), D52 and H52, (0) D70 and H74.
Both the behavior of MSD predicted by the slit geometry and the one predicted by the triangular geometry are generally consistent with the increase in burn-off degree for all carbons of the series, so that this analysis is not sufficient to decide which geometry is more appropriate to describe the structure of activated carbons. However, our simulation and characterization method allows us also to obtain the behavior of the isosteric heat of... [Pg.397]

Figure 5. Minimum (circles) and maximum (triangles) values of q t as a function of d for slit geometry pores... Figure 5. Minimum (circles) and maximum (triangles) values of q t as a function of d for slit geometry pores...
In Section VI we shall apply this correction to the results of Bennewitz (1969) when slit geometry was used and the angle y was quoted. Stolte (1972) has shown that some conclusions were significantly altered after application of this correction. [Pg.400]


See other pages where Slit geometry is mentioned: [Pg.1400]    [Pg.27]    [Pg.364]    [Pg.99]    [Pg.608]    [Pg.415]    [Pg.77]    [Pg.57]    [Pg.57]    [Pg.259]    [Pg.25]    [Pg.141]    [Pg.413]    [Pg.230]    [Pg.234]    [Pg.236]    [Pg.60]    [Pg.12]    [Pg.391]    [Pg.392]    [Pg.395]    [Pg.396]    [Pg.396]    [Pg.398]    [Pg.409]    [Pg.20]    [Pg.64]    [Pg.400]    [Pg.205]    [Pg.1400]    [Pg.588]    [Pg.747]   
See also in sourсe #XX -- [ Pg.435 , Pg.436 , Pg.453 , Pg.457 , Pg.467 ]




SEARCH



Slits

© 2024 chempedia.info