Polarography residual current

The concentration of As(III) in water can be determined by differential pulse polarography in 1 M HCl. The initial potential is set to -0.1 V versus the SCE, and is scanned toward more negative potentials at a rate of 5 mV/s. Reduction of As(III) to As(0) occurs at a potential of approximately —0.44 V versus the SCE. The peak currents, corrected for the residual current, for a set of standard solutions are shown in the following table. 

Commercial polarographs are also available in which the voltage scan is carried out automatically while a chart recorder plots the current-voltage curve. A counter-current control is incorporated which applies a small opposing current to the cell which can be adjusted to compensate for the residual current this leads to polarograms which are better defined. Most of these instruments also incorporate circuits which permit the performance of alternative, more sensitive types of polarography as discussed in Section 16.9... 

This assumption was supported by the fact that the residual current observed by potential scan polarography at the W/DCE interface was larger in Range C than that in other ranges, indicating the increase of the capacitance due to the change of the interfacial structure. 

Residual current in polarography. In the pragmatic treatment of the theory of electrolysis (Section 3.1) we have explained the occurrence of a residual current on the basis of back-diffusion of the electrolysis product obtained. In conventional polarography the wave shows clearly the phenomenon of a residual current by a slow rise of the curve before the decomposition potential as well as beyond the potential where the limiting current has been reached. In order to establish the value one generally corrects the total current measured for the current of the blank solution in the manner illustrated in Fig. 3.16 (vertical distance between the two parallel lines CD and AB). However, this is an unreliable procedure especially in polarography because, apart from the troublesome saw-tooth character of the i versus E curve, the residual current exists not only with a faradaic part, which is caused by reduction (or oxidation)... 

Unfortunately, AB and CD are often far from parallel as a consequence of the complicated nature of the residual current in polarography (cf., pp. 118-121), where one has to deal with at least two or three factors, as follows. 

AgCl electrode) and the cathodic current due to the reduction of hydrogen ion begins to flow at about -1.1 V. Between the two potential limits, only a small current (residual current) flows. In curve 2, there is an S-shaped step due to the reduction of Cd2+, i.e. Cd2++2e +Hg <=t Cd(Hg). In DC polarography, the current-potential curve for the electrode reaction is usually S-shaped and is called a polaro-graphic wave. 

Residual Current A small current that flows in the solution free of electroactive species (see curve 1 in Fig. 5.10). The residual current in DC polarography is mainly the charging current, which is for charging the double layer on the surface of the DME (Fig. 5.13).6)... 

If we measure a residual current-potential curve by adding an appropriate supporting electrolyte to the purified solvent, we can detect and determine the electroactive impurities contained in the solution. In Fig. 10.2, the peroxide fonned after the purification of HMPA was detected by polarography. Polarography and voltammetry are also used to determine the applicable potential ranges and how they are influenced by impurities (see Fig. 10.1). These methods are the most straightforward for testing solvents to be used in electrochemical measurements. 

The residual current in polarography is the small current observed in the absence of an electroactive species. 

What are the sources of the residual current in linear-scan polarography ... 

M level thus we understand why the ratio of limiting current to residual current degrades badly at a DME in this concentration range. Charging current, more than any other factor, limits detection in dc polarography at a DME to concentrations above 5 X 10 M or so (Section 7.3.1). 

This capacitive current does not usually form discrete waves of its own but is the major cause of the residual current. This capacitive current increases with increasing potential and so creates the slope of the upper and lower plateaux of polarographic waves. It is a background signal, a source of noise, and as such it is a major limiting factor on the sensitivity of dc polarography. 

The difference is discussed in the succeeding text.) Within the voltage range of 0 to -0.3 V versus SCE only a small residual current flows. It is conventional in polarography to represent cathodic (reduction) currents as positive and anodic (oxidation) currents as negative. The residual current actually comprises two components, a faradaic contribution and a charging or double-layer current contribution ... 

Carbon paste electrodes have acquired greater importance in the field of electrochemistry due to their low residual current and noise and because they are very economic and easy to prepare and replace. These electrodes have a wide range of anodic and cathodic applications. Electrode surface modification is a field of great importance in the modem electrochemistry especially due to the various applications. Some electrochemical techniques, such as differential pulse polarography, stripping voltammetry, differential pulse voltammetry and square-wave voltammetry have been widely applied for the determination of pharmaceuticals. 

Fig. 4.6. Method for determining the concentration of residual impurities, [Impjj jjj., in a reaction mixture if the impurity is a catalyst or co-catalyst. The observed variable x can be peak-height h for a GLC method, absorbance A for spectroscopy, conductivity k for conductimetry, current i for polarography, or rate constant k for kinetics, etc.

---