Osmotic pressure, molecular weight

Rayleigh X Rs, particle size Applicable for (R/X) < 1/20 extension of the Rayleigh equation to solutions allows the measurement of osmotic pressure, molecular weight, and turbidity of colloidal or polymer solutions see Section 5.3... 

Figure C2.1.8. Reduced osmotic pressure V l(RTc as a function of the polymer weight concentration for solutions of poly(a-metliylstyrene) in toluene at 25 °C. The molecular weight of poly(a-metliylstyrene) varies...

The phenomena we discuss, phase separation and osmotic pressure, are developed with particular attention to their applications in polymer characterization. Phase separation can be used to fractionate poly disperse polymer specimens into samples in which the molecular weight distribution is more narrow. Osmostic pressure experiments can be used to provide absolute values for the number average molecular weight of a polymer. Alternative methods for both fractionation and molecular weight determination exist, but the methods discussed in this chapter occupy a place of prominence among the alternatives, both historically and in contemporary practice. 

As noted above, all of the colligative properties are very similar in their thermodynamics if not their experimental behavior. This similarity also extends to an application like molecular weight determination and the kind of average obtained for nonhomogeneous samples. All of these statements are also true of osmotic pressure. In the remainder of this section we describe osmotic pressure experiments in general and examine the thermodynamic origin of this behavior. 

Figure 8.9 is a plot of osmotic pressure data for a nitrocellulose sample in three different solvents analyzed according to Eq. (8.87). As required by Eq. (8.88), all show a common intercept corresponding to a molecular weight of 1.11 X 10 the various systems show different deviations from ideality, however, as evidenced by the range of slopes in Fig. 8.9. 

The solute molecular weight enters the van t Hoff equation as the factor of proportionality between the number of solute particles that the osmotic pressure counts and the mass of solute which is known from the preparation of the solution. The molecular weight that is obtained from measurements on poly disperse systems is a number average quantity. 

These results show more clearly than Fq. (8.126)-of which they are special cases-the effect of charge and indifferent electrolyte concentration on the osmotic pressure of the solution. In terms of the determination of molecular weight of a polyelectrolyte by osmometry. ... 

What makes the latter items particularly important is the fact that the charge and electrolyte content of an unknown polymer may not be known hence it is important to design an osmotic pressure experiment correctly for such a system. It is often easier to add swamping amounts of electrolyte than to totally eliminate all traces of electrolyte. Under the former conditions a true molecular weight is obtained. Trouble arises only when the experimenter is indifferent toward indifferent electrolyte this sort of carelessness can be the source of much confusion. 

In some lUPAC-sponsored researchf, samples of the same polystyrene preparation were distributed among different laboratories for characterization. The following molecular weights were obtained for one particular sample by osmotic pressure experiments using the solvents, membranes, and temperatures listed below ... 

As in osmotic pressure experiments, polymer concentations are usually expressed in mass volume units rather than in the volume fraction units indicated by the Einstein equation. For dilute solutions, however, Eq. (8.100) shows that

partial molar volume of the polymer in solution, and M is the molecular weight of the polymer. Substituting this relationship for (pin Eq. (9.9)gives... 

Table 9.3 lists the intrinsic viscosity for a number of poly(caprolactam) samples of different molecular weight. The M values listed are number average figures based on both end group analysis and osmotic pressure experiments. Tlie values of [r ] were measured in w-cresol at 25°C. In the following example we consider the evaluation of the Mark-Houwink coefficients from these data. 

Thus we have finally established how light scattering can be used to measure the molecular weight of a solute. The concentration dependence of r enters Eq. (10.54) through an expression for osmotic pressure, and this surprising connection deserves some additional comments ... 

Molecular weights of polysaccharides in solution can also be measured by osmotic pressure and light scattering. Osmotic pressure yields the number average molecular weight, which can be usefully used with Mw from sedimentation equilibrium as a measure of polydispersity Preston and Wik [28] have done this for example with hyaluronic acid. The ratio Mw/Mn the polydispersity index is often given as a measure of polydispersity, and can be related to the width of a molecular weight distribution via the well-known Herdan [96] relation ... 

The number average molecular weight is required. This is obtained directly from measurements of a colligative property, such as the osmotic pressure, of dilute polymer solutions (see Chap. VII). It is often more convenient to establish an empirical correlation between the osmotic molecular weight and the dilute solution viscosity, i.e., the so-called intrinsic viscosity, and then to estimate molecular weights from measurements of the latter quantity on the products of polymerization. 

Fig. 116.—w/c plotted against c for several fractions of polystyrene in toluene at 30°C. Molecular weights of the fractions are indicated by the numbers appearing with each curve. The osmotic pressure n is expressed n g./cm.2 (Results of Krigaum. )... 

If 0.6 N lithium bromide is added to the solution of the polyelectrolyte and also to the solvent on the opposite side of the osmometer membrane, the lowermost set of points in Fig. 145 (lower and left scales) is observed. The anion concentration inside and outside the coil is now so similar that there is little tendency for the bromide ions belonging to the polymer to migrate outside the coil. Hence the osmotic pressure behaves normally in the sense that each poly electrolyte molecule contributes essentially only one osmotic unit. The izjc intercept is lower than that for the parent poly-(vinylpyridine) owing to the increase in molecular weight through addition of a molecule of butyl bromide to each unit. 

---