Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Metal-support interactions reduction temperature effect

The initial reaction rate values show the effect of metal support interaction, the extent of reduction and method of preparation. For alumina supported sample the increase in reduction temperature, and an increase in the degree of reduction, results in a fourfold increase in initial... [Pg.533]

Ceria/noble metal (such as Ru, Rh, and Pd) catalysts are composed of noble metal species such as nanoparticles and clusters dispersed on the ceria supports. The catalysts show typical strong metal-support interactions (SMSI) (Bernal et al., 1999), that is, the catalysts exhibit a number of features for SMSI effects including (1) reducible supports (2) "high temperature" reduction treatments (3) heavily disturbed chemical properties and significant changes in catalytic behavior of the dispersed metal phase (4) reversible for recovering the conventional behavior of the supported metal phase. In these cases, the reducibility of ceria NPs is greatly enhanced by the noble metal species and the catalytic activities of the noble metals are enhanced by ceria NPs. [Pg.300]

Nanostructural Features of Metal-Support Interaction Effects in NM/Ce(M)02, Catalysts. Their Evolution with Reduction Temperature. [Pg.137]

When considering metal-support interaction effects, the whole set of Electron Microscopy data presented in the previous section point out some important differences between the behaviour of noble metal catalysts supported on ceria and that of titania-supported catalysts. Much higher reduction temperatures are required in the case of ceria-type supports to observe nanostructural features similar to those described for the so called SMS I efTect. [Pg.151]

Palladium-silica catalysts prepared from tetra-ammine palladous nitrate (to avoid chlorine introduction) showed a marked reduction effect , viz, the specific activity for benzene hydrogenation decreased with increased reduction temperature, i.e., 573 or 723Various explanations were considered, including a metal-support interaction. After reduction at 873 K, X-ray diffraction provided clear evidence of chemical reaction and at lower temperatures silicon insertion into palladium might still occur, which could either disrupt the palladium ensembles required for benzene adsorption or modify the properties of single palladium atoms, if these are the active sites. [Pg.64]

Fig. 4.38. The effects of various pretreatments (oxidative and reductive) on CO oxidation on a 40-nm Pt/ceria model catalyst prepared by colloidal lithography as measured by the temperature of 50% of CO conversion and the apparent activation energy from the Arrhenius plot. CO reduction was made in 0.5% CO for Ih at 573K, H2 oxidation (a-treatment) was done at a = Ph2/(.Ph.2 + P02) = 0.33 at 573 K for 1 h, and finally /3 = CO oxidation (/3-treatment) was done in the O-rich regime (oxidative conditions), /3 = Pco/ Pco + P02) = 0.2 with 0.3% CO and 1.2% O2 at temperatures between 300 and 673 K. It is seen that reduction leads to a lower Tbo and activation energy, while sustained CO oxidation leads to an increase of the activation energy, which is not recovered by reductive treatments. The latter is explained in terms of strong-metal-support interactions (SMSI) and particle reshaping (see text)... Fig. 4.38. The effects of various pretreatments (oxidative and reductive) on CO oxidation on a 40-nm Pt/ceria model catalyst prepared by colloidal lithography as measured by the temperature of 50% of CO conversion and the apparent activation energy from the Arrhenius plot. CO reduction was made in 0.5% CO for Ih at 573K, H2 oxidation (a-treatment) was done at a = Ph2/(.Ph.2 + P02) = 0.33 at 573 K for 1 h, and finally /3 = CO oxidation (/3-treatment) was done in the O-rich regime (oxidative conditions), /3 = Pco/ Pco + P02) = 0.2 with 0.3% CO and 1.2% O2 at temperatures between 300 and 673 K. It is seen that reduction leads to a lower Tbo and activation energy, while sustained CO oxidation leads to an increase of the activation energy, which is not recovered by reductive treatments. The latter is explained in terms of strong-metal-support interactions (SMSI) and particle reshaping (see text)...

See other pages where Metal-support interactions reduction temperature effect is mentioned: [Pg.229]    [Pg.285]    [Pg.173]    [Pg.9]    [Pg.62]    [Pg.87]    [Pg.241]    [Pg.266]    [Pg.136]    [Pg.103]    [Pg.103]    [Pg.104]    [Pg.106]    [Pg.121]    [Pg.159]    [Pg.160]    [Pg.219]    [Pg.155]    [Pg.424]    [Pg.21]    [Pg.37]    [Pg.60]    [Pg.136]    [Pg.170]    [Pg.156]    [Pg.60]    [Pg.95]    [Pg.95]    [Pg.96]    [Pg.98]    [Pg.113]    [Pg.152]    [Pg.509]    [Pg.29]    [Pg.90]    [Pg.176]    [Pg.180]    [Pg.185]    [Pg.190]   
See also in sourсe #XX -- [ Pg.173 ]




SEARCH



Effective interaction

Effects interaction

Interactive effects

Metal support effects

Metal support interaction

Metals temperatures

Reductants, effectiveness

Support effects

Support interaction

Supported interactions

Supported metals reduction effect

Supported metals reduction temperature effect

Supported metals support effect

Temperature reduction

© 2024 chempedia.info