Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Lifting lugs

Fig. 13. Exploded view of an OxyTech MDC-55 ceU a, end plate b, rim screen c, side screens d, tube sheet e, full-cathode tube f, half-cathode or end tube g, side plate h, lifting lug i, punched and coined stiffener strap j, bosses k, end plate, operating aisle end 1, hydrogen outiet m, connector bar n,... Fig. 13. Exploded view of an OxyTech MDC-55 ceU a, end plate b, rim screen c, side screens d, tube sheet e, full-cathode tube f, half-cathode or end tube g, side plate h, lifting lug i, punched and coined stiffener strap j, bosses k, end plate, operating aisle end 1, hydrogen outiet m, connector bar n,...
The baseplate shall be provided with lifting lugs for at least a four-point lift. Lifting the baseplate, complete with all equipment mounted, shall not permanently distort or otherwise damage the baseplate or the machinery mounted on it. [Pg.46]

Lifting points and lifting lugs shall be clearly identified. [Pg.55]

Lifting lugs shall be provided in the cover plate for lifting the pnmp assembly, inclnding the driver. [Pg.64]

B022 Four point lifting lugs F LIFT LG C 1 lyes (true) 0 no (false)... [Pg.196]

Lifting lugs attached to the equipment shall be designed using a maximum allowable stress of one-third of the specified minimum yield strength of the material. [Pg.76]

During campaigns for 155-mm projectiles, the lifting lugs are fed to the ERD. At those times, the ERD is used only to move materials, and the induction heating coils are not activated. The vent gases from the ERD are sent to the MPT quench tower. [Pg.70]

Shipping orientation—pay close attention to lift lugs and nozzles. [Pg.366]

Lifting lugs should be plainly marked with capacity to indicate whether they are for lifting the saddles alone or the entire vessel... [Pg.380]

At the initial pick point, when the vessel is still horizontal, the load is shared between the lifting lugs and the tail beam or lug, based on their respective distances to the vessel c enter of gravity. As the lift proceeds, a greater percentage of the load is shifted to the top lugs or trunnions until the vessel is vertical and all of the load is then on the top lugs. At this point the tail beam or shackle can be removed. [Pg.387]

The same trunnion could have a lifting lug welded to the end of the trunnion (Type 1). This lug also produces circumferential and longitudinal moments in the shell. However, in addition this type of lug will produce a torsional moment on the shell that is maximum of 0° and zero at 90° of angular rotation. The rotating lug (T) pe 2) eliminates any torsional moment. [Pg.387]

See other pages where Lifting lugs is mentioned: [Pg.1068]    [Pg.26]    [Pg.23]    [Pg.27]    [Pg.310]    [Pg.310]    [Pg.311]    [Pg.54]    [Pg.340]    [Pg.5]    [Pg.58]    [Pg.166]    [Pg.87]    [Pg.761]    [Pg.1104]    [Pg.126]    [Pg.27]    [Pg.891]    [Pg.568]    [Pg.518]    [Pg.33]    [Pg.1235]    [Pg.79]    [Pg.23]    [Pg.491]    [Pg.106]    [Pg.34]    [Pg.1236]    [Pg.1072]    [Pg.39]    [Pg.74]    [Pg.81]    [Pg.366]    [Pg.380]    [Pg.416]    [Pg.442]   
See also in sourсe #XX -- [ Pg.163 ]



SEARCH



Lifting

Lifts

© 2024 chempedia.info